# 1
Convert-A-Ball Ball Mount for 2" Hitches - 6-3/4" Rise, 8" Drop - 10,000 lbs
I use this hitch when I pull my horse trailer to make the stop/start transitions as smooth as possible for the horses in the back. It works great. I also love that its a category IV hitch. Really heavy duty. My truck sits pretty high, and the amount of drop - 8" is perfect. I never worry about hitch failure travelling with my horses - they're a heavy load, and any failure would be a disaster. E Trailer provided excellent service, and their shipping to Canada was prompt and hassle free. Way to go guys, keep up the great work!
I have a 2012 GMC Sierra HD with a 12" suspension lift. I recently purchased a ball mount hitch with 8" inch drop for our 36' RV trailer and it worked great. It took 3 days for the hitch to get to me. Great service from e-trailer.
# 2
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
Good, very solid ball mount with just the extra rise I needed, 2 3/4", to get level trailer and good clearance for the trailer jack. But excessive shipping charges from etrailer, $[XX] for an $[XX] purchase. Found out to my cost later that [online vendor] would have shipped for free.
As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !
# 3
Flash Secure Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise
Very strong, easy to install and very secure. Yes a bit pricey, but well worth the money. I did notice there was what I thought was an unusual amount of play in the receiver. I called etrailer and Marcia was so very helpful and very concerned that I may have received the wrong product. She even called the manufacturer and found out what the changes that were made by the manufacturer which made the pictures incorrect. My hat is off to Marcia and all the folks at etrailer
ball mount fits loosely in the receiver so that the pins that extend out from the ball mount shaft through the holes in the receiver don't extend out far enough, for my liking. This is because since the ball mount shaft has so much play, it will shift to one side. Then, the pin on the other side does not extend all the way out of the hole so that it is not flush. True, i am being paranoid. However, i imagine a case like a crash where enough force could pull the shaft out from the not fully extended pin side to release the trailer to wreak more damage. I would just feel more secure if the pins went out further through the receiver or the shaft was not so loose. Otherwise, i really like the product a lot... enough to give it four stars... :o)
# 4
Convert-A-Ball Cushioned Multi-Hitch Clevis and Pintle Hook Combo w/ 3 Balls - 2" Hitches - 10K
No problems with the hitch- makes it easy to switch between trailers! I have no complaints!
Very good product and I would have given it a 5 star rating but there is one critical flaw that is quickly remedied. When using the pintle hitch, the pressure exerted on pin while pulling a load can cause the pin to turn, thereby popping out the keeper pin. This happened twice and it was a good thing that I had the hitch positioned so that the pintle pin was installed going down allowing gravity to hold the pin in place even when the keeper pin fell out. I have since changed out this style of keeper pin with a cinch pin that can spin 360 degrees inside the 2" tube and no pressure is exerted on it by the load being pulled. If I were designing this from new, I would make it so that the draw pin on the pintle had a square shoulder much like a carriage bolt so that it can't turn thereby eliminating pressure on the keeper pin. Other than that it is a great product.
# 5
Flash Self-Locking, Aluminum Ball Mount - 6" Drop, 5" Rise - 10,000 lbs
Excellent hitch. I like that it is made from one piece of solid aluminum and so much easier to lock and unlock. No more fumbling around under the bumper trying to unlock the hitch pin.
Just what I'd hoped for. Extremely light-weight and easy to install/remove. Perfect mount for my new Jeep Cherokee!
# 6
Curt Solid 2-Ball Mount for 2" Hitches - 2" and 2-5/16" Balls - 10K - Black
Very solid.. great product !!!
This thing is very solid and heavy duty; it weighs in at 16.8 pounds. I haven't pulled with it yet, but I believe it's exactly what I needed to pull the two trailers I need to pull (2" ball, and 2 5/16" ball).
# 7
Pro Series Tri-Ball Mount for 2" Hitches - 1-7/8", 2", 2-5/16" Balls - Black
Not only did I get the parts I needed at a great price. They were delivered they day after I ordered them. Great communication from my salesman. I will definitely be a return customer.
Heavy duty hitch. Well built and welds are fine.
# 8
Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs
Shipping was a mess, lost the first one in the mail somewhere because no one thought a 50# hitch would punch through cardboard. It is working as expected, but does not seem to be a true 2" drop.
Easy ordering, fast shipping and a quality product. I can't believe how much this Brophy Ball Mount Hitch weighs! Incredible.
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"