# 1
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 2
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 3
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 4
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
The Curt trailer hitch and wiring harness for my 2016 Highlander was a perfect fit. Installation was a breeze just following the etrailer videos. I opted for the 4" drop ball mount because of the Highlanders ground clearance but the standard 2" drop would have been just fine. Will use etrailer again without hesitation.
I purchased this hitch to pull my utility trailer with. It was easy to order, arrived on time, and simple to install/use. This hitch is built very well and strong, and has a good coating finish on it. Great product!
# 5
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 6-5/8" Rise - 3,500 lbs
Great Product! After installing a Curt (C11184) Hitch on my '08 BMW 135i convertible, I needed a drawbar and ball. I really liked the elegant design and one piece simplicity that this one has. It is very sturdy and the dimension measurements were accurate. The whole reason I got it was to trailer my new (old) wood boat home from the barn I found it in. Once the hitch was on and the (56146KIT) Wiring kit was installed. This drawbar slid right in. Thanks to the accurate measurements the trailer sat at the perfect height the first time.
works great
# 6
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Purchased for a Hyundai Elantra. After a 2" ball is mounted, there is about 7.5" from the top of the square shaft to the top of the ball. This is what was needed to get the center of the ball 18" off the ground for most U-hual trailers. This design has no plate edge protruding below the square shaft. This helps reduce scraping when going over bumps, which is an annoying issue with my other ball mount. I would have much preferred the euro ball mount, which has a nice 45' bend to avoid scraping, and a ball that will never vibrate loose, but one was not offered with this much rise. The ball mount is well made of solid steel, not a hollow tube. Finish quality is excellent. The mount does not come with the locking pin needed and so that must be ordered separately with the ball. Item was packed a little loose in the box and was clanking around with the other item I bought, but they did not get scratched up.
What our customers are saying:
"very easy to shop"