# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Installing onto my 2014 Silverado 1500 was a breeze. The only thing that caught me off guard was that I needed to cut a portion from the center of my splash guard for the rear bracket to be able to mount. I was only expecting to trim/remove the air dam as etrailer explained in the item description, which I still had to do. Other than that it was a perfect fit and I'm happy with the results. I plan to use this for a snow plow, winch, and many more interchangeable items for it.
I installed this front hitch by myself on a 2016 Chevy Suburban in about 3.5 hours with no floor jack. I use it to carry my mountain bikes when we are towing the trailer. The hitch sits 8.25” off the ground and extends out past the air dam about 3.5”. Once installed, the hitch is not very noticeable. A couple notes on the install: 1. The most difficult part is figuring out where to make the hole in the splash shield for the rear mounting point. I removed the splash shield and determined roughly where to cut a 1.5” hole based on the existing holes in the cross member. 2. To cut the air dam, I drilled small holes the the corners then used a utility knife to score and cut out the section. 3. I mounted the rear point first which gave me leverage to install the front easier. 4. The tape method for the 9/16 hardened washer and cone washer did not work for me. I had to finagle them into position as I was tightening the bolts (huge pain) 5. I had 4 extra 9/16 hardened washers. These are apparently supplied in case you need additional washers to fill the gap in the frame. I am very satisfied with this product and would definitely recommend it to others.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great VIDEOS and helpful questions and answers service. Fit my 2014 Silverado present and I had a good idea how the job would go before the hitch even showed up.A little slow on the shipping but other than that very happy with my purchase.
Purchased a front mount receiver hitch for my pickup from etrailer.com. The hitch mounted exactly as it said and was a super to install. I plowed snow all winter with a receiver plow. Now I move three times the snow now in a third of the time.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product is great! Exceeds my expectations for ease of installation and performance. I removed the 3” spoiler completely vs cutting for hitch. The key is to “dry fit” in place and use a metal punch to mark all your drill holes. Wire bolt feeder worked great for installing bolts. I used the hitch to mount my eight pole rod & cooler holder for surf fishing.
Super fast shipping,but could use better packing.Hitch actually made a large hole in box,UPS driver had me check to see if anything was missing.Easy install,but try finding a 17/32" bit. After seeing how big the front opening is I just used a 1/2" bit. I think it took longer to remove, trim and reinstall the front spoiler than the rest of the job. Looks great installed
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
For a business that is based on shipping everything they need to learn how to package stuff. Everything I received from a trailer comes damaged at this point.
Installed on my 2019 GMC Sierra 1500 Denali. Shipping box was destroyed & poorly packed. Instructions were straightforward. Install took 1 1/2 hrs. I only trimmed the thin trim without cutting the skid plate. The receiver pushes up on the skid plate slightly, but I didn’t want to cut it. Should work great for my E-bikes when pulling the RV.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitch was well-made, and installing it was very easy. However, the design of the hitch is somewhat perplexing. The hitch receiver hangs about 3 inches lower than it needs to, which reduces the ground clearance on the front of the truck significantly. See attached photos. The hitch will work until I find something better, That restores the front ground clearance
Well so far so good. It was a little difficult trying to do it by myself, got most of it done and then had to go to a autobody shop down the road to tighten up the 4 bolts.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
2002 Chevrolet SilveradoThe hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2014 Ram 1500If I could mark it at 4.5 stars I would. I like it the hitch. I think it hangs down too low, only 8" off the pavement. I did not like to have to take off the tow hooks to install the hitch. I did like the idea of I sold the tow hooks for almost as much as I paid for the hitch. I had to buy a hitch extender. ( I do not see the extender I bought on etrailer listed any more.) The extender put the hitch out far enough to clear the grill guard that I had installed. My goal was to have a place to mount my 8,000 pound winch. I can now slide the winch in the front receiver or the back factory receiver. I can now pull the truck out from either front or back.
This front mount hitch was just what we needed to haul our bikes when camping with the slide in camper. We had to take the bikes and a bike hitch off each time we had to get in the camper when we stopped. This front mount hitch saved us from having to do that. Also use it for a carrier to carry extra luggage. It came fast and it was very easy to install, just as advertised.
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.
# 9
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Install went perfectly. It all bolted up just how the instructions said it would. The hardest part was navigating your tools in the tight spaces. Having the deep sockets as suggested is definitely worth it. I was also able to utilize a cordless impact wrench and it helped a ton. This will work great for our bike rack.
Delivery was super fast, instructions and instructional video was excellent. Installed my new part in less than 40 minutes
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!
VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very sturdy hitch, extremely easy install. If you already have your air dam removed there is no cutting or modification at all, completely bolt on. Make sure you have both front load bearing washers centered before you completely bolt down the hitch. I didn't need any alignment washers on the back brace it was very level as is, if you are using this for winching keep in mind it will affect your approach exit angles. Overall a great product!
The "no drill" aspect is really nice. The wire bolt guides are a huge helper. The instructions are very good except for detailing where to cut the trim. This lead to me cutting more than I would have needed to. That part was not good. I recommend having vehicle up on ramps and then using a car jack to support weight of the hitch as it is quite heavy to hold up as you begin to assemble to the frame.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The packaging needs additional crush protection. While it’s difficult to damage a trailer hitch, the box was mangled and the hitch is missing paint and has jagged edges of flaking paint all over. I’ll spend time repairing the finish on the hitch after paying good money for what should’ve been a product in brand new condition.
Perfect fit on my 2020 Chevy 2500HD. I didn't even have to trim the lower plastic spoiler. Install took about 20 minutes. Can't wait to try it out for my motorcycle carrier. As always, etrailer gives great, speedy service.
# 15
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great customer service and product.
The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.
Of the many hitch receivers I have purchased, the front mounted ones have never failed to surprise me of their usefulness! From bike racks, to carrier for coolers, to my chainsaws, gas and oil, they make it work. Recently while cutting wood for a hunting lease engagement, I put a second ball on the front and used it to drive a 16' trailer up a hill to get the wood where it was needed for offloading. Backing it up had resulting in damaged trucks, trailers and numerous attempts. Using the front hitch it was a one and done deal! Love it! I have even used it to pull trees over when felling. I don't have enough fingers and toes to count the uses! If you have ever thought about it, just stop and order! You won't regret it!
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very easy to install. works great for bike rack and generator box.
After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .
# 18
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2007 Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
These is an excellent hitch at an excellent price. The install was easy and all the hardware that is needed is in the box. I chose the Drawtite over the Curt because the receiver end is a little longer. It' not even noticeable on the truck. I have a snow plow that attaches to the hitch. The Toyota cap shown in the picture was not included. The Tundra is a 2020 so I can confirm if fits.
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
1998 Ford F-150 and F-250 Light DutyGreat product,easy installation and dealing with etrailer has been a real good experience.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."