# 1
Adapter 4-Pole to 7-Pole and 4-Pole
Really nice trailer wiring adapter. Very easy install. Takes about 30 minutes with all the tools needed. Drill, 7/64 bit for pilot holes to mount the bracket, flat blade screwdriver and 11/32 nut driver and two #10 self tapping metal screws with locking split washers and a couple zip ties to tidy up the wiring harness.
I looked at so many options before deciding on the B&W hitch, but I have no regrets buying it. There is nothing that my car is suitable for towing that this thing can’t accommodate. I even use it on the front hitch of my mower to move trailers around the yard! Adjusts very easily and stows nicely (though on my Ford Edge it rides lower than I like when stowed).
# 2
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
7 pin connector separated from cable. I was expecting that "Molded Cable" meant that the connector was fused to the cable insulation but instead, the two separated almost immediately after I installed it. It still works fine as the wires are connected securely inside the connector but with the outer covering pulled out like this, I don't think it will last very long.
Çable good but after putting new 7way plug on truck cable wire colors did not match etrailers picture
# 3
Hopkins Endurance Multi-Tow 7-, 5- and 4-Way Flat Trailer Connector - Vehicle End - Ergonomic Design
Works great and etrailer folks did an outstanding job with quick turnaround and communication…thank you!
Exactly what we had been looking for. Now I can hook up multiple trailers with different connectors and all the electrics on each trailer works. I mounted mine directly to the receiver hitch frame. The biggest challenge for us was routing the backup wire from the taillight housing, through the body of the truck to the connector. the rest went together fairly easily. Seems to be pretty solid and looks much better than the loose pigtail connector it replaced.
# 4
48" Long 4-Pole Loop with Cover
The items I ordered will allow me to adapt my utility trailer for transporting my sea kayaks. Curt and Hopkins are both quality manufacturers. On a shipping note, the box arrived at the Post Office broken wide open. Your shipping folks need to wrap small, heavy, items in bubble wrap. Then stabilize it with foam peanuts. Just putting it in a box then stuffing the box with craft paper does not cut it. Items were not damaged so I am good to go.
I have now installed the following on my 2017 Wrangler: Brake light relay kit . Hopkins Towed vehicle Tail Light wiring kit. Blue Ox base plate. Blue Ox Patriot Portable RF Braking System. All of this has taken about 3 days of work spread out over a week or so. Overall it went well. Not too many surprises. Crawling around under a car at 71 is a bit of a strain but I'll get over it. I must say that Donna P. has been a wonderful source of great information and has stayed right on top of the process. eTrailer has been a great source for this project. I would recommend you all with no hesitation.
# 5
Hopkins Endurance 6-Way Trailer Connector Socket - Vehicle End - Ergonomic Design
The stuff not here
Very difficult to make the wiring connections, I was afraid I’d have problems on down the road so, I took it out of circuit and threw it away
# 6
fits the plug perfect....just got a goldwing used, haven't had a chance to ensure it (the bike) was wired correctly for a trailer. no fault of the product, just wish its wireing was a bit long due to the way the plug was intigrated into the underside of the tour trunk.
Works great! Took a few minutes to figure out the rv side and get it set up so the round RV part Correlated in the correct way to the standard four flat wiring. But it went smoothly.
# 7
Adapter 4 Pole to 6 Pole and 4 Pole Trailer Wiring Adapter
This adapter really cleaned up the installation and connected directly to the wiring harness. Maybe added an additional 20 mins to install this adapter but totally worth the time and money.
II use it on my towed vehicle behind the motor home. It allows me to take motor home power to a trickle charger in the towed vehicle and connect to the towed vehicle wiring. The four prong receptacle provides outlet to be used if there is ever in need for a four prong fitting good.
# 8
Adapter 7 Pole to 4 Pole with Tester and Cover
ETrailer had exactly what I wanted at a fair price. Website was easy to navigate and purchasing was simple. Shipping was fast and I was kept notified right up to when I received my order.
Plugs in easily, shows that pins are producing voltage, and locks in place using the spring loaded door to the 7-pin.
# 9
Hopkins Heavy-Duty Trailer Coiled Wire Adapter for 7-Way to 4-Wire Flat
Works, exact fit, high quality, coils tight so max of about 3.5’ perfect! Heavy duty wiring, great waterproof connections.
Item was just as I anticipated. It looks good, works great, and the delivery was as promised. E Trailer is a good place to do business.
# 10
Quick Fix (TM) 4 Pole Flat Car and Trailer Ends
They have just what I needed and it arrived very quickly.
I have used etrailer probably four or five times now and have been very happy. Shipping is fast, prices are reasonable and the products are of good quality. I purchased more of the Quick Fix 4 Pole Trailer Ends - they work really well for the non-automotive industrial control project I am working on.
# 11
7-Way Molded Trailer Wire Connector, 6' Long
Only gave 4 stars because it was a bit confusing. I have a lot of auto wiring experience; from car stereos,amplifiers and all manner of accessories. All of the info on etrailer indicated that the color coding didn't match up. So I went into it disregarding the standard color coding, when in fact it was just as it should be.
Good thick rubber and plug works perfectly.
# 12
Hopkins Endurance 7-Way Trailer Connector Socket - Vehicle End - Ergonomic Design
Well I wasn't able to use this as there was no good place to install on my car without it practically dragging. Not a product problem at all. I tried to return and customer service was fast and super helpful... unfortunately return shipping would eat up any refund. So.. I get to keep it. good quality and product. Very happy with it and wish I could use it. Will keep it for sometime in the future when of course I will need it.
I bought this socket for my 2006 Volvo Xc90 to wire in the 4-Pole harness I also purchased from etrailer. Already had a few 7 Blade to 4-Pole adapters from my previous vehicle, and wanted the option of adding a trailer brake wire for a small camper later on so that was the main reason for the purchase. It also went very well with the Hidden Hitch I had already installed, bracket mounted right up to the existing tabs on the hitch. Super quick and easy install, as all of my etrailer purchases have been. Looks great on the truck, and functions great with the 180 Degree cover.
# 13
Hopkins 6-Way Connector with Jacketed Cable - Trailer End - 8' Long
The plug was missing the set screw and collar that compresses on the cable to prevent strain on the connectors when removing the plug. You can see the set screw clearly in the product picture.
I like this style of plug because it is molded and is important in keeping water out of the plug. It is conveint because it has the right colored wires. I have a water tight termination box with studs that it is wired into. Once I damaged the cable so I opened up the terminal box installed eyelet lugs on the spare pigtail, and installed it in a fiew minuets. I keep a spare on hand with lugs on it so if I have an accident I can quickly replace it. I also use these on some of my smaller tow behind equipment. that's why I like this size plug it isn't real bulky.
# 14
7-Way Molded Trailer Wire Connector - 3' Long
I've had this in use for over a year and they don't build them like they use to. I use this on a gooseneck trailer and the piece of plastic behind the spade connector for the clearance lights and brakes has melted, allowing the spade connector to lose contact with the plug on the pickup. So the lights would cut off in the middle of the night and would have to wiggle the connection till I could fix it. I have an older Hopkins plug and never had this problem. To fix the problem I ended up putting pieces of thin copper wire behind the spade and have done it twice since the plastic melted a 2nd time and once again the trailer clearance lights would quit working. Attached are before and after pictures.
After a year doing its job well.
# 15
Hopkins Endurance Multi-Tow 4-Way Flat to 7-Way RV Trailer Adapter w/ 4-Way Vehicle End Plug
Worked out pretty good. Had a hard time figuring out just how to attach it. I ended up just zip tieing it. It was a life saver that I could pull the rear plug apart. Made it possible to slide part of the harness thought a tight hole.
Got this to replace the poorly constructed plug that came with the 7pin wiring kit. That plug broke at the spring hinge the second time I used it. Surprised that Hopkins didn’t include “Butt Connectors” though. Seems a little nickel dimeish. Had a good experience with Paul who refunded their price for the defective Kit plug as well as refunding the price difference for the wiring kit which had gone from $110 to $48. Overpriced to begin with but convenient. Paul did real good dealing with a pissed off Old Guy
# 16
Adapter 7-Pole to 6-Pole - Universal
We had been having trouble with our other adapters, no brakes or intermittent brakes. This adapter fits better than any of the others ever have, great connection and is holding tight. I will be picking up some more of these. The only downside to me was they came on the value shipping which is rather delayed for us and I would rather pay to get it here more quickly. I was needing it and it was several days getting here. We ship a lot and I know shipping directly with USPS goes faster than that and is not expensive.
Added the gooseneck trailer plug in bed and I wanted to be compatible with new and old style plugs. Adapor worked great.
# 17
6-Pole Square Trailer Wiring Connector Kit (Car and Trailer Ends)
Bullet-proof connector, if not the most elegant. Used in my case for custom "adventurization" wiring on my 2007 BMW F800ST motorcycle, now just road tested this late summer - early fall 2017 on a three month, 18,000 mile loop out of Chicago through the Arctic & Pacific Northwest, including the Dempster & Dalton Highways. Had a custom wiring harness that had to be able to be removed in order to get at the engine, hence the need for the connectors. A few photos should be attached.
This is a product that I needed for my project, but was not easily found and available. etrailer.com not only had the product, but had it at a great price. Shipping was very fast and free for the amount I ordered. Overall, this was a great shopping experience. I made a bulk order of 16 as I am manufacturing trailers that are towed behind motorcycles. This product gives me the six conductors that I need in a very small package, which is great due to the size of motorcycles compared to cars or trucks. The only thing that could be improved with this product would be if they came with dust caps for each connector, or at least one for the vehicle side to prevent dust and moisture intrusion while the trailer is not in use. Keep up the excellent service and selection.
# 18
Hopkins Endurance Quick-Install Trailer Connector Adapter - 4-Way Flat to 7-Blade
It took awhile to receive my order, but I was informed by e-mail and was kept informed when I should expect delivery. Luckily, was in no rush, so I would reply and wait for an update from you. i received the connector in good condition. Thank you!
Installation went well and works fine. Only issue was the screws included with the product were not the right ones so had to replace which wasn't a big deal.
# 19
Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Vehicle End
I recently had a need for the Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Vehicle End - HM48190 to replace the faulty one on my van. It was easy to find what I needed on the site and the price was comparable to other sites I had visited. I decided to go with etrailer because I had previously ordered the hitch through them. I appreciated the fact that an email was sent out confirming that they received the order as well as a follow-up email telling me that the part was shipped along with providing the tracking number. The installation of the part was easy and took no time to complete. Overall it was a fine experience and if I need to order anything in the future, I will be sure to come back and order from etrailer.
Great product. Easy to install
# 20
Hopkins Endurance 4-Way Flat Trailer Connector - Trailer End - Ergonomic Design
I rewired my light bar for my boat trailer with the items I purchased. Before I built the the light bar, every time I used my boat trailer I would waste valuable sailing or fishing time repairing faulty lights. The do not last long when you submerge them in salt water. This light bar now version 3.0 have given little trouble over the years
Great product. Works well when I had a broken connection on my 4 way plug end on my light-up hitch cover I bought from y'all a while back. Always a happy customer. Thanks, George.
What our customers are saying:
"Quick processing, and delivery. reasonably priced very satisfied"