# 1
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 2
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Well made, quality product.
# 3
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
# 4
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 5
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 6-5/8" Rise - 3,500 lbs
Great Product! After installing a Curt (C11184) Hitch on my '08 BMW 135i convertible, I needed a drawbar and ball. I really liked the elegant design and one piece simplicity that this one has. It is very sturdy and the dimension measurements were accurate. The whole reason I got it was to trailer my new (old) wood boat home from the barn I found it in. Once the hitch was on and the (56146KIT) Wiring kit was installed. This drawbar slid right in. Thanks to the accurate measurements the trailer sat at the perfect height the first time.
works great
# 6
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
What our customers are saying:
"Excellent customer service. Best on-line ordering experience yet!"