Summer Starts Here - Save up to 70%
# 1
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
I ordered this to replace the straight young that came with the trailer hitch on my Q5 that was too low to the ground. The 4 inch lift was exact What I needed.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 2
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 3
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 4
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
Purchased a vehicle with a class 2 factory hitch installed. This was the proper drop to haul my band trailer. First trip went without an issue.
# 5
Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
This is a stylish and attractive ball set up that looks less 'trucky' than most. No, I never noticed it before I bought one, either.
I ordered a euro style, stinger. It arrived quickly. I would use Etrailer.com again, and recommend it to others. Also, I had to ask customer service some questions, which I don't remember. I do however, remember them answering those questions, in a friendly manner. So good customer service as well, which is hard to find, any more. Do businesses with this company. They are earning it.
What our customers are saying:
"Great product. fast, professional, and well communicated service. it was a pleasure buying from y'all. thanks again"