# 1
Curt Hitch Receiver Reducer Sleeves - 3" to 2-1/2" or 2"
Dont know what say, they are going to build this truck in april!! Thanks for quick service,cant wait to install.Thanks
product worked out just fine / GREAT!!!
# 2
TorkLift Cannon Hitch Extension - 3" Ford Super Duty Factory Hitch - 36" Long
The hitch worked great. I pulled a 12ft Wells Cargo enclosed trailer with a motorcycle on board. The reason I purchased this hitch, I have a 101/2 ft Lance camper that extends pass the bumper. I used it on a F350. I did use a Equla-I-Zer sway control hitch because of the tongue weight of my trailer and I believe it made this extension hitch work better.
This is a quality product and works perfectly! Easy to install and adjust. They even give you extra chain and turnbuckles.
# 3
TorkLift Cannon Hitch Extension - 3" Ford Super Duty Factory Hitch - 48" Long
One person install with the truck camper on the truck. Super simple. I used my rolling kobalt shop stool to carry the 48” extension’s weight when I slid it into the receiver. Easy peasy. I have a 2019 F350 DRW (8’ box) and a 2021 Arctic Fox 1140 with the Fox Landing. 48” was perfect. My Yakima bike rack is great with the Fox Landing up and the bike rack swings down when I want to lower the stairs. Highly recommend.
Thank you for reaching out. After I received some of the missing parts I was able to use few days later. I'm still missing parts that were never shipped that I used 1/2 steel plate between my hitch and the 2 Grade 8 bolts used in the extension to snug and stop bouncing. So other than that. I'm able to tow my boat with my truck camper. But i would like to havr all the parts...
# 4
Buyers Products 3" to 2" Receiver Tube Adapter
Unfortunately this receiver adapter did not fit my Ford F250 3" hitch, way too tight. Worked with Arthur from e-trailer to obtain a return/refund. After looking at reviews, I see many other folks had the same issue. If I were e-trailer I would pull this item from my product offering.
When I went to use this my bike rack would not fit in the 2" receiver because it was poorly made. Unfortunately it was well past etrailers 60 day return policy so they told me they would not help me. I contacted buyers myself and they were happy to help me and took the old one back and shipped me a new one that works great. If buyers did it for me, they certainly would have done it for etrailer but etrailer couldn't be bothered with it. I will buy buyers products again but will not buy anything from etrailer anymore. They also told me I would need to buy a whole new $XXX base for my bw companion hitch because the parts were not available. A quick call to bw and my. $XX parts were on their way. Again,poor service from etrailer. Back to local shops for me.
# 5
TorkLift Cannon Hitch Extension - 3" Ford Super Duty Factory Hitch - 42" Long
Just got it this afternoon and removed my old oneand installed this new one. The box was in bad shape from trip, but the hitch extension and accessories were all there and in good shape. Looks like a much better setup than I had. Thanks for a good product and great service. Not very common these days, but greatly appreciated!
She's boxy...and a little heavy...but she's good! If using with a truck camper, save your back and put it on before the camper goes in the bed.
# 6
B&W Hitch Receiver Reducer Sleeve - 3" to 2-1/2"
I love the small ears on the edge that prevent this Sleeve from sliding into the 3” receiver while trying to slide in a hitch. After a year shows little signs of rust even though it has been left on the truck entire time. Of course I leave on the truck since I have a locking hitch pin.
Good quality, it's going work out great for the time until I upgrade to a better hitch.
# 7
Draw-Tite Reducer Sleeve with Collar - 3" to 2-1/2"
Well made now can open tailgate
As stated the front hole on the reducer is 3/4”. I will weld a 5/8 piece of pipe in the reducer to make it work for me. That same reducer with two 5/8” holes would be great but I will make it work. I have a 3” receiver on my f350 with a 5/8” pin so I don’t know why the would make the reducer with a 3/4” pin hole. As always though you have great products and service. Thanks
# 8
Trailer Hitch Receiver Reducer Sleeves - 3" to 2-1/2" or 2"
Quick and easy ordering and delivery. The hitch receiver reducer sleeve fits perfectly.
Exactly as described. Fit down to my 2" hitch items. It was slightly difficult to get all sleeves and item aligned and insert the hitch pin but we made it.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."