# 1
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product Quality: 5/5 Customer Service: 5/5 Packaging: 0/5 Stars The people on here complaining about packaging are not being prima donnas. The first time I ordered this, all I got was the banged up crossbar with the shredded packing label taped to it. Customer service was great, and shipped out a replacement within hours. The second arrived in the shredded remnants of the box with about 75% of the hardware. License plate holder is banged up, the powder coat is busted through. I'm just going to buy the replacement pieces at the hardware store. There's no point in wasting another week to find out if whoever handles their packaging can pull off the bare minimum of competence this time. The picture is the condition the box arrived in (open and shredded). You can actually see the first crossbar with the shipping label attached at the edge of the photo. My advice would be to order this elsewhere, on the off chance you'll actually receive it intact. It's a shame, the people seem really nice, and the item quality is stellar.
Extremely disappointed, again. Box arrived with a hole in it and hardware laying on the ground. Seriously? I can hardly wait to see what I am missing. The last two products I ordered were a complete failure as well. Sent a message to customer service and never heard back.I've spent way too much money at this company.
# 2
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
# 3
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Bolted right up to my 2019 F-250. Looks like it's going to work perfect to haul my E-bike rack. I might have to use a dual receiver hitch to drop the rack down for better visibility while driving. That's to be determined. I'd highly recommend the Eco Hitch!!
The hitch is great! Super stout. But, installation was a disappointment. There was a significant gap between the frame rails on the Ford. About 3/8 inch. Did some research and it seems some frames are different but can't confirm. I happen to have a piece of 3/8 steel plate that I was able to cut and drill and slide it in to take up the gap. Definitely extra work I wasn't planning on doing. I guess I'd still buy it again but if you're going to pay someone to install it then make sure they put a nice spacer in there and bot a bunch of washers. Again, not sure is this is a Ford inconsistency or an eco hitch problem. Because it's a hitch and needs to be 100% solid this should be looked into.
# 4
EcoHitch Invisi Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Review for truck front hitch receiver I finally Installed the front receiver hitch today, I pulled it out of its package and found all parts wrapped to the receiver hitch good call as there was a hole in the box. The license plate holder received some damage it was bent some. Installation. I reviews the video prior and read the instructions. Had to purchase a 4 inch hole saw and a torque wrench that added to the cost of the hitch. Installation was for the most part straight forward, when the video cuts from shot to shot I now know all the cussing and swearing are done during that time as it’s very difficulty to get the hitch in over/under the exiting hardware, solo installer took me 3.45 hrs to install, tight fit under the truck to maneuver under the truck. Bolts back into original tow hooks was a total Pain in the A$$ trying to hold up the hitch and the hooks while trying to maneuver the hold back in. (Had to take it out as I inserted on the wrong side) I will say that installation is doable by novice front yard mechanic but with a difficulty of 7 out of 10, trying to get the bolts torqued to specs is difficult due to clearance and angle of the bolts. Make sure you have deep well sockets because the new bolts for the hitch and long and a standard size socket will not be able to grip the nut as you tighten it down to specs. Put the bike rack on the hitch receiver and found that the hole that we drilled out to put the hitch in is not big enough. The bolt for the hitch goes in from the right and there was barely enough room to get it in the hole, used a wrench to tighten it but it was slow going, the other issue was that on the left side there is a hitch lock I struggled to get it on, but then could not reach in to remove the key. So final outcome was I had to drill out another 4 inch section of the bumper to get to the key. If your hitch has a bolt on bike rack like the swagman e-bike rack you want it to be secure so the bolt is a must this option may not be the best option. The bikes block the headlights so no night driving with the bikes on the rack. The handlebars need to be folded down otherwise the bikes will ride too high on the front and obstruct your vision. If I had to do it again I would have gotten the hitch that is lower and would not have to drill out my bumper, and it would have given me more visual clearance. I did take a shot drive with the bikes in front it will take a bit to get used to them being in the front as well as making wide turns while towing the RV that I don’t take out the car in front of me.
My friend installed the hitch and I helped . But mostly by staying out of his way!?? Everything worked out perfectly!!! Thank Y’all for the Great Service
# 5
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Let me start by saying this is not the first front receiver I've purchased from etrailer all my trucks get front receivers for winches. This time though the box shows up on time but the corner is blown open and the receiver is hanging out. Also the bag of bolts has been ripped open and half the bolts are loose in the open box but to my surprise after counting everything, they were all there.spray foam packing would have mitigated all that. Moving on. Went to install the receiver and the end mounting plates are 1/4 inch too tight. Won't fit the frame rails. Had to spread each side 1/8 out with a Hydraulic bottle jack. Apparently using a jig during the manufacturing process is optional these days. After all that I finally got it to fit good. It looks good and the welds seem adequate. I think it could have been installed in an hour by myself if not for having to "adjust" it but was still done in under 2 hours.
Mounted the EcoHitch hidden front mount trailer hitch on 2011 Ford F 250 with a Ranch Hand Grill Guard. The Ranch Hand uses two of the same holes as the EcoHitch's four mounting holes. Getting the pieces lined up is a bit of a challeng although no modifacations were necessary.If I have the need to do it again I would let an installation shop do it. etrailer's customer service and commuication are excellent, shipping time and delivery were very fast.
# 6
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Easy install !! Looks great ! No lift to install worked off floor and used floor jack to lift in place . Would be easier with 2 people . 2023 Chevrolet 2500 High Country Duramax 4wd .
This is a very sturdy and well-made hitch. Installation was fairly straight forward - the directions and video are very good. My truck is a 2024 Silverado 2500 HD in High Country trim (why pay less?) so, the fairings/moldings under the front bumper were slightly different, but nothing that was not easy to adjust to. The measurements in the instructions were right on. As you can see in the photos, we have two ebikes that we plan to haul around while we pull our camper. The hitch and bike rack set up appears to be very secure and stable. They sit a little higher than I would like, but not any higher that the snowplow lights I had on a truck I has way back in the day... I'm pretty good at backing the camper (28 ft), but I am also looking forward to testing out pushing the camper into it's fairly tight parking pad. I've never done it, but I hear it works well in close spaces. Lastly, this is the second hitch I have purchased from etrailer. We added one to the back of the wife's Rav4 last fall to haul this same bike rack and bikes. It also works great (tight, stable and secure) except note that the Toyota installation was a little more challenging as there is very little room to work & insert the bolts, however, no cutting was involved. It looks nice. In any case, both transactions were great. If I had another vehicle that needed a hitch, I would purchase it again from eTrailer. Much thanks to all.
# 7
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2016 Sprinter 2500 wagon (meaning 3 bench seats with windows all the way around) 4 cyl Diesel - BOLT ON PERFECT NO ISSUES ! Shopped hard for this, best weight, best install, best front hitch for my vehicle
Easy to install. Works perfect to hook up car trailer to front of rv when camped for days at the track.
# 8
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
When I realized my backordered front hitch for my F-350 wouldn't be here for my deadline, etrailer had a perfect alternative in my hands within 48 hrs of change order!Audrey was more than helpful, & install was straight forward with the instructions. The installation video for a similar hitch was enough to figure the rest out. NOTE: When cutting the hole in the valance, make your hole roughly 1/4" smaller than suggested and make a diaginal relief cut on all 4 corners to slip over the lip of the reciever. Also some trimming of the aluminum valance bracket was required, but easy enough.
Fast shipping. Great solid HD front hitch. No drill. Easy installation. No snaking bolts, no rerouting any transmission lines. 2022 F350 dually 7.3 gas, this is the one
What our customers are saying:
"Wow! I placed my order late on a Friday afternoon and when I get to work this AM my I have confirmation that my order has already shipped. Thanks for the great service."