Most Popular Vehicle End Connector for 2013 GMC Terrain

Works great and etrailer folks did an outstanding job with quick turnaround and communication…thank you!

Exactly what we had been looking for. Now I can hook up multiple trailers with different connectors and all the electrics on each trailer works. I mounted mine directly to the receiver hitch frame. The biggest challenge for us was routing the backup wire from the taillight housing, through the body of the truck to the connector. the rest went together fairly easily. Seems to be pretty solid and looks much better than the loose pigtail connector it replaced.

Click to Enlarge

Click to Enlarge

I used the Hopkins 3 to 2 converter to make a 6-pin round to 4-flat connector for my Winnebago View motorhome. While there are 6-4 plugs available to do this, they do not work on the Winnebago View (no brake lights). This adaptor works great.

This device was no help in connecting my five wire trailer to my four wire goldwing. I ended up having to use a number of diodes in the trailer wiring to make everything work properly. My trailer had red LEDs that were used for Brake, Turn & stop and I had to get the brake and turn function to share the same lead on the light fixture.

Well I wasn't able to use this as there was no good place to install on my car without it practically dragging. Not a product problem at all. I tried to return and customer service was fast and super helpful... unfortunately return shipping would eat up any refund. So.. I get to keep it. good quality and product. Very happy with it and wish I could use it. Will keep it for sometime in the future when of course I will need it.

I bought this socket for my 2006 Volvo Xc90 to wire in the 4-Pole harness I also purchased from etrailer. Already had a few 7 Blade to 4-Pole adapters from my previous vehicle, and wanted the option of adding a trailer brake wire for a small camper later on so that was the main reason for the purchase. It also went very well with the Hidden Hitch I had already installed, bracket mounted right up to the existing tabs on the hitch. Super quick and easy install, as all of my etrailer purchases have been. Looks great on the truck, and functions great with the 180 Degree cover.

Click to Enlarge

Click to Enlarge

Click to Enlarge

This is the product I expected and it arrived in factory new condition. To no fault of etrailer.com the currier wagon train and the ox’en that pulled the load were heading East. This was not the direction they were accustomed to so it took a few extra days. All in all good job I will do more business with this company.

I wish than all trailer wiring was color coded the same. I have wired a lot of trucks ant trailers and trouble shot problems and always solved the problems. this one gave some serious thinking since the wiring was color coded different. But it is working and I do like the Pollak plug.

Hitch for 2018 EcoSport SES. Easy to install and looks good. Wire end with cover also looks good

Click to Enlarge

Click to Enlarge

Product was awesome. My last two connectors have corroded so bad within a year that I constantly was having to take a wire brush and clean off the pins to get good contact. I'm waiting to see what the environmental cap does to eliminate me having to do this. Also bought the vehicle side. Would highly recommend this to anybody with a trailer hook-up. Only thing I would suggest is to make sure anybody purchasing also buys the splices since none come with the product. All in all, a great buy. Thanks!

SMI Stay in Play Duo installation in 2015 Jeep Wrangler Unlimited – Packaging was great with everything needed included plus extra items for various installation methods of you’re choosing. Upon initial investigation and survey, everything except the CD Information pack was accounted for. No big deal, as I had previously watched 2 different Youtube installations found on the internet. In fact, the internet videos were what I used as my step by step installation process, and the written instructions were only used for concerns where the video may not have been as clear as I had hoped for. Understanding that everyone has their own style and methods for doing this project, I purposely was not in a hurry to rush through it. All in all, I took @ 8 hours to install the Adapter 4 to 6 pole #30637, the EZMount Tow lights Kit, and the Stay in Play Duo Braking System. I choose the EZMount because I didn’t want to mess around with the OEM taillights and wiring. Magnetic lights don’t work so well on composite tops and I didn’t want to stick them to the sides of te Jeep, so I modified the EZ mount to wrap around the thickness of the rear glass hatch on both sides. I added a 2”x 4” pc of Velcro on the inside of the glass hatch and the mating surface of the plastic light housing - to hold the lamps in place until the rear gate was closed. I ran the wire harness on the inside under the trim all the way up to the front and through the grommet in the firewall. The flat 4 wire was routed and secured up to the Adapter 4 pole to 6 pole that I had fastened to the Blue Ox base plate. The actual installation of the SMI unit and assorted parts went rather smoothly. Most difficult issue was the lack of working space in front of the driver’s seat area. Installing the screw that holds the G force controller on the front (the side towards the front of the car) was difficult as it was almost a blind installation due to lack of room. The nut and fender washer used through the fire wall for attaching the air cylinder cable bracket was a challenge to reach - tight fit with not much room for one's hand and arm. Other than that, no big surprises – just a lot of tedious steps to do when you want to be sure that it is being installed properly – take your time and don’t be in a hurry. Once everything was installed – it all worked when I checked the system out. The only thing that may seem a bit odd is that when setting the G force initially, the compressor will shut off while adjusting per instructions. To do this initial adjustment, the wife stepped on the brake in the Motorhome, with the switch “On”. The compressor starts, and the brake is pushed down by the Air Cylinder, at which time I slowly adjusted the G force until the compressor shuts off. I secured the adjusting bolt and I told the wife to take her foot off the brake and then re-apply them. The compressor did not start again and the air cylinder did not apply the brakes in the Jeep. After setting the G force per instructions, the unit didn't turn on when the brakes in the Motorhome were applied - but since we were not moving - all I can assume is that the brake system will function while slowing down once the accelerometer setting (the sensitivity setting on the G force box) has been met. I assume that the sensitivity setting method includes a way to ensure the Jeep brakes are not engaged too frequently and only until needed. This is the only step that is a tad bit confusing without an explanation as to what to expect once the G force sensitivity is set. Lastly, I checked the brake away switch and it turned the compressor on and applied the brakes as expected. Overall - the installation went rather smoothly. Can't wait to see how the product works once we hit the road. I'll check back and provide an update later.

Click to Enlarge

Click to Enlarge

looks okay.

We just finished a makeover of our 1995 boat trailer. New bunks, sanded and painted but the best part of the project was the new LED lights from your company. They are so much brighter than the old incandescent bulbs that you really do feel safer driving down the road. We pulled the 20 year old wire out and replaced with new and used the 3M scotch loks to tie in. We were not sure the new style grommets would fit the old holes in the frame but they fit great. Your customer service was great, alerting me to a backordered reflector but recommended a replacement that worked fine. Patrick set up a Q&A page for me since I had questions about the best way to protect connections with dielectric grease, heat shrink and tape. Your website is one of the best with ease of navigation, complete pictures, great selection and thorough info, dimensions, etc. You guys really have your act together and also offer great value. I would not hesitate to purchase again and will recommend you when I can. I have attached a couple of pictures. Thanks for all your help. Wayne N.

Click to Enlarge

Click to Enlarge

Easy to install and works great.

I found what I thought I needed on the website to prepare our car to be flat towed, but wanted to call to verify. After a short phone call, eTrailer saved me about $50 and got me the stuff I actually needed to get the job done! I won’t shop anywhere else!

This part is an exact replacement to the part that failed. The failure was caused by a poor installation which allowed the rubber boot to chaff on the truck frame. As it was an exact replacement installation was straight forward although I modified the mounting bracket to prevent a reoccurrence of the problem.

Used this as the connection point for the Roadmaster diode wiring kit. Seems to be well made and will hopefully last a long time. I did spray paint it flat black so it blends into the front bumper of my “toad” a little better.

Click to Enlarge

The documentation for wiring is limited and difficult to read without magnification. Otherwise this is well made and works perfectly.

great product

The plastic plugs don’t hold up very well in the bed of the truck to plug in the 5th wheel trailer in nothing can beat the metal ones

I fitted the Hopkins 5-way flat connector harness with a 5-way round plug which couples to my Goldwing trike (tow vehicle). The popup trailer lights operate as designed.

Connector and wire harness well made - connector designed such that it can be mounted and harness has added protection for wires. Would like to have marine grade wire since I do mostly saltwater fishing. I mounted the connector on a piece of 1.5" square galvanized tubing painted black.

Click to Enlarge

Click to Enlarge

Worried as first because the picture with instruction showed an adapter and I had a curved surface on my GMC Terrain at the mounting point. Worked great and did not een have to take the ld pigtail off.

Products were shipped same day I ordered, received parts whitin 3 days of ordering. Parts were exactly what I had been looking for.

Excellent Quick Delivery When you are driving a Test or NASCAR Hauler you need replacement parts very quick, just like a pit stop. Thank You very much for the rapid delivery. Mint Moore III Ford Performance Race Hauler Driver

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

A great little heavy duty plug that I use to connect my car to the rv when towing 4 down.

I explained to Roger (I believe was his name) that I have a Blue Ox tow bar and base plate, The base plate was installed along with the wiring kit, but did not include the wire to go from the front of the grill to the interior of my Jeep to plug in my RVi brake, and this is what he sent me. I'm attaching a picture of what I have on my vehicle. Not only was it the completely wrong part, but it arrived in damaged packaging which I did not open. Please send return instructions.

Click to Enlarge

After a year this connector is still working fine. No complaints.