# 1
Gen-Y Hitch 5th Wheel to Gooseneck Pin Box - Auto Latch - Lippert 1621/1621 HD - 21K - 3.5K TW
Great replacement for the Curt Turning Point pin box! Easy to install and took a couple hours since I did it by myself. I had to purchase new 5/8” locknuts as the originals from the Curt install needed replacing. I also had to buy (4) 5/8” nuts from Tractor Supply since the Curt install had nuts welded on the front 4 bolt locations. I used the Curt 5/8” bolts and flat washers since they did not need replacing. I haven’t had a chance to get the trailer on the road yet, but see no reason why it will not pull nicely with the Gen Y gooseneck. It will be pulled with a 2022 Chevrolet Silverado 2500HD 6.6 Duramax and 10 speed Allison transmission.
This hitch reduced chucking very well, I have a 2004 3500 Dodge Ram 4x4 Conestoga riding truck with very stiff suspension, the torsion action of the hitch definitely helps when crossing bridges and pot holes. The 5th wheel is an older Keystone Copper Canyon that is in great shape. I Have 12K miles with the new hitch.
# 2
Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert 1621/1621HD - 30K GTW - 4.5K TW
Great replacement for the Curt Turning Point pin box! Easy to install and took a couple hours since I did it by myself. I had to purchase new 5/8” locknuts as the originals from the Curt install needed replacing. I also had to buy (4) 5/8” nuts from Tractor Supply since the Curt install had nuts welded on the front 4 bolt locations. I used the Curt 5/8” bolts and flat washers since they did not need replacing. I haven’t had a chance to get the trailer on the road yet, but see no reason why it will not pull nicely with the Gen Y gooseneck. It will be pulled with a 2022 Chevrolet Silverado 2500HD 6.6 Duramax and 10 speed Allison transmission.
The Gen-Y gooseneck has been excellent! I now have approximately 12k miles on mine and it rides very nicely with very limited chucking and handles rough roads very well. I’d highly recommend that you contact Gen-Y BEFORE ordering to ensure you get the correct load rating product. Gen-Y and Etrailer have provided excellent customer and tech support! This product definitely frees up your truck bed and does require a precise line up to hitch.
# 3
Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert 1621/1621HD - 30K GTW - 5.5K TW
Great replacement for the Curt Turning Point pin box! Easy to install and took a couple hours since I did it by myself. I had to purchase new 5/8” locknuts as the originals from the Curt install needed replacing. I also had to buy (4) 5/8” nuts from Tractor Supply since the Curt install had nuts welded on the front 4 bolt locations. I used the Curt 5/8” bolts and flat washers since they did not need replacing. I haven’t had a chance to get the trailer on the road yet, but see no reason why it will not pull nicely with the Gen Y gooseneck. It will be pulled with a 2022 Chevrolet Silverado 2500HD 6.6 Duramax and 10 speed Allison transmission.
This product is a chucking ENHANCER, not a chucking dampener. Additionally, despite what you have read, my experience with GenY customer service has been terrible. GenY will not support their warranty program, they will try to tell you everything is OK, when the fact is, their product is faulty and does not function to GenY product literature statements “Built-In Suspension Creates Up to 90% Smoother Ride”. I purchased the GenY executive hitch from eTrailer on 3/10/23, etrailer sent the wrong unit and to etrailer’s credit - they quickly took responsibility and replaced with the correct unit on 3/24/23. I installed on my DRV Elite Suites PS3 just in time to attend the SOITC rally at the Outer Banks on 4/13/23. When we left for this 750-mile one-way trip, the GenY load indicator was in the middle of the green zone, I measured the pin load at 5,200 pounds. Bedrail clearance was my reason for buying the GenY, it replaced a Trail Air on my DRV and a Reese 27,000-pound hitch on my 2022 F450. Bottom line, the GenY system provided no improvement in bedrail clearance, but did offer the ability to switch in different gooseneck balls to adjust for bedrail clearance. GenY states that a 1,000-mile break in period is required before the GenY torsion system is fully effective. My experience was that at 750 miles the torsion system on the GenY had sagged to it lowest point with the load indicator in the unit outside of the green, this also resulted in losing nearly two inches of bedrail clearance. It looks like it has a metal-to-metal stop so that the lowest the indicator will go is to the white lines outside of the green. I called GenY from the RV park and was told that the unit would not sag further. I purchased a Curt gooseneck ball which was 2 inches higher than the Ford ball to regain bedrail clearance having to rapid ship it to the RV park. Chucking became downright scary on the 750-trip home. As an example, chucking was induced every time my truck’s ten-speed transmission shifted up. Upon arrival home, I again contacted GenY customer service with a full expectation that GenY would replace the unit. Instead, here is their response: “I spoke with our QC Manager regarding your hitch. He said that you are in the correct unit and being at the top end of the green is normal after the break-in miles. As for the bedrail clearance he said that you would be able to lower the pin box down a set of bolts (with our pin boxes you are only required a minimum of 4 grade eight bolts per side) or use a B&W ball as they are roughly 1 1/2” taller.” This is unacceptable...
# 4
Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter - 20,000 lbs
Installation was a breeze. I have not towed with it yet, but am sure it will perform as expected.
Hitch is great. Delivery went well. My only issue is I was able to find it for roughly $xxx cheaper on [online]. When I reached out to customer support to let them know, they told me it was too late to cancel the order and if I’d like, I can return it for a $xxxx shipping fee…
# 5
Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert Turning Point - 21K - 3.5K TW
Great replacement for the Curt Turning Point pin box! Easy to install and took a couple hours since I did it by myself. I had to purchase new 5/8” locknuts as the originals from the Curt install needed replacing. I also had to buy (4) 5/8” nuts from Tractor Supply since the Curt install had nuts welded on the front 4 bolt locations. I used the Curt 5/8” bolts and flat washers since they did not need replacing. I haven’t had a chance to get the trailer on the road yet, but see no reason why it will not pull nicely with the Gen Y gooseneck. It will be pulled with a 2022 Chevrolet Silverado 2500HD 6.6 Duramax and 10 speed Allison transmission.
I have towed now for a few thousand miles since changing to this pin box and honestly wish I had done this years ago! It tows so much better than my 5th wheel box did! Feels more stable, no more bucking and so much softer and better feel when towing! Not to mention so much less hassle dealing with a 5th wheel hitch!
What our customers are saying:
"I would have never thought that an internet site would provide such a useful service. I was able to locate a hard to find item, purchase it, ship it for free, track it and install it myself using the detailed instructions. This site has far exceeded my expectations. I will never purchase anywhere else. I have also told every one in all the clubs and forums I am part of that this is the ultimate one-stop-shop."