# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I am not sure that installing this hitch could have been easier. I did it on the ground on my driveway, sloped, by removing my tow hooks and supporting the receiver on some blocks and bolting it in place directly into the frame. The hardware fit perfectly in alignment and thread size etc. We've mostly used it to carry bicycles when towing, though once placed a trailer with it also. Strong, fully functional and as noted easy to install.
Haven’t had a chance to use the front hitch on our Nissan Frontier year but the installation was quick and easy. I was all set to knock the installation out in 20 minutes until one of the split lock washers failed and had to be replaced out of my spare stock. Also an additional note: the hitch showed up heavily scratched despite the packaging having been in good condition. Maybe some more careful handling at the warehouse is in order.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
Terrible, they sent the wrong hitch and now want me to pay shipping for the return
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?
# 7
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2007 Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."