Most Popular Fits 1-1/4 Inch Hitch for 1996 Mercury Villager

Exactly as described and quickly shipped.

Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

Click to Enlarge

Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.

Exactly as described and quickly shipped.

This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.

Click to Enlarge

Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.

Click to Enlarge

Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.

Service from eTrailer was great, they even wrote to ensure I got the order correct when I ordered a different size hitch cover than the drawbar that I ordered. Picture attached of the somewhat unique application for the Euro style setup I’m using – I’m dragging my race tires to racing events with my 750HP Cobra!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Excellent fitment and gives my trailer a level stance.

Click to Enlarge

Click to Enlarge

For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.

Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.

Click to Enlarge