Yes, the TorkLift PowerArmor Locking Battery Box # TLA7700L will comfortably fit your 2 Renogy batteries in it since each battery measures 13.1" Wide x 6.9" Deep x 8.6" High. view full answer...
The # FV807357 Fan-Tastic Vent Roof Vent Assembly Upgrade Kit will work for your 2019 Lance 2185 Travel Trailer if the opening meets the requirements. In order to install this vent, you must have a 14-1/4" x 14-1/4" opening approximately in the trailer's roof and ceiling and the roof can be no more than 4" thick.
These are standard dimensions for a vent opening. If this does not work for you please send measurements and I will do my best to find a solution.
I have attached a review of... view full answer...
Your 2020 Lance 2375 travel trailer will have came with #10 Torflex axles rated at 3,900lbs per axle. The Torflex Lift Kit # K71-707-02 will provide you with 4 lift blocks for your trailer since you have tandem axles. It will provide you with 2-5/8" lift for your trailer.
Since you are lifting your trailer you will likely need more Leveling Blocks # UF48-979051 for the stabilizers and tongue jack. And a couple Adjustable Steps # SASA-10C-G will make stepping into your camper easier since... view full answer...
The PD4655LIV unfortunately is no longer in production you'll need the Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel # PD4655V instead. This will also simply replace the converter section of your current power center and has a lithium jumper on the circuit board to adjust your charging profile from lead acid to lithium.
As for the solar, this system is going to be completely independent from the your power center. Solar begins at the panels up on the roof... view full answer...
Looking at the BAL Retract-A-Spare it has a much different design than the Lippert Spare Tire Winch # LC159056 you found. You may be able to mount the new winch so it will still work on your trailer but as we do not have both the products here with your trailer I can not guarantee you will not need to make any modifications. Please refer to the images below for their mounting dimensions. view full answer...
The only possible double step upgrade option we have for a 2018 Lance 1475s is the Flexco Manual Pull-Out Steps for RVs part # SMFP-2100. It looks like the only dimensions that won't match up is the mounting flange bolt spacing which is larger on this double so you will need to drill a few holes is all.
To determine how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match the height of the steps when... view full answer...
We have options for a suspension system for your 2020 Lance 1995 travel trailer, but it uses torsion axles, which are not something we offer, so the best alternative we can provide is an axle-less system, the Timbren Heavy-Duty Axle-Less Trailer Suspension.
The Timbrens are simply bolted or welded on so you do not have to worry about finding an axle that meets any specific measurements. The simplest way to install it is to use a piece of 2-inch by 3-inch tubing through the integrated hole... view full answer...
Thanks for reaching back out!
It looks like the Replacement Fan Motor Assembly Kit for Dometic FanTastic Roof Vent Fans # FVK8017-00 will actually work with the FV7300 model as well so it's exactly what you're needing! We've confirmed this with Dometic/Fan-Tastic so it will be a guaranteed fit. view full answer...
Based on the 6,000 lb GVWR of your tandem axle 2011 Lance 2185 travel trailer, the option that is most likely to work is the Torflex Lift Kit - Tandem Axle # K71-707-02.
However, you do need to verify that your Lance travel trailer has a Dexter #10 Torflex axle with a capacity between 2,300 and 4,000 lbs, which is something that should be on the axle tag or sticker. If that's what you have, the # K71-707-02 is the right kit for you. view full answer...
You'd want to go with a cover that is slightly longer than what your camper is so since yours is 15-1/2 feet in length the Camco UltraGuard part # CAM45771 would be what you'd need as it fits up to 16-1/2 feet in length. view full answer...
Yes, the Mount-n-Lock Heavy-Haul'r Replacement RV Bumper # MNT43VR can be mounted on your 2020 Lance 1685 travel trailer. You will need to cut the factory bumper off and mount the included brackets to the extensions off the frame for the factory bumper. view full answer...
The promo stickers on the sides of the Lippert Smart Jack Electric Trailer Jack w/ Footplate # LC643589 are not a replaceable part. You can however use a cover like Ultra-Fab Protective Cover for Electric A-Frame Jacks # UF38-944020 to prevent any more weathering to the stickers or other parts of the jack head going forward.
If you know anyone with a Cricut machine then you could have them make you a custom wrap for your jack head to match the trailer as well. view full answer...
It does not look like you will be able to use the Lippert Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 on your 2020 Lance 2285 travel trailer unless you switch your fold up rear steps to a set of fold in steps like the MORryde StepAbove RV Steps # MR78RR that will fit inside your door. This is due to the rear jacks needing to mount between 18" and 48" behind the bolt that holds the rear leaf spring on your camper.
I have linked the installation... view full answer...
Yes, the GVWR of a Lance 2565 travel trailer is around 7,300lbs and the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 is designed for use with trailers up to 10,000lbs.
I've attached a short video below where Dave will walk you through the installation process if you choose to put these on yourself. view full answer...
If you're looking for a complete system to replace your current jacks then the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 will be a great option for your Lance 1985 travel trailer. These jacks combined have a total capacity of 10,000lbs which is well over the GVWR of your trailer.
If you have LCI OneControl and wifi in your trailer then you can also use the app on your smartphone or touchscreen in your trailer to control your jacks. Installation... view full answer...
You'll have two options when it comes to a two panel system:
Option 1: Go Power Overlander Solar Charging System with Digital Solar Controller # GP39MR. These panels have a hard frame and would require you to drill into the roof of your trailer. They are 59-1/8" L x 26-5/16" W and provide up to 380 watts.
Option 2: Go Power Solar Flex Charging System with Digital Solar Controller # 34272628. These panels have a soft, flexible base to fit curved surfaces and can be glued to the roof instead... view full answer...
Ok, we have some options for you, and I should note that bike racks do need to be approved by their manufacturer for the use on the back of travel trailers like your 2021 Lance 2185. There aren't any travel trailer approved racks for a 1-1/4 inch hitch, but from what I could see it does look like this trailer has a bumper. So what you can do to add bikes in the rear of the trailer, so long as the bumper is 4 to 4-1/2 inches tall, is add a Swagman rack:
- Swagman Traveler XC2 Bike Rack... view full answer...
The Torflex Lift Kit # K71-707-01 is the most likely cantidate for your 2014 Lance 1575 Travel Trailer. This will provide you with 2-5/8" of lift. You will want to ensure that you do have the correct side mount torsion axle. Your bolts should pass through the side of your frame on 8" centers for the axle mounts. If you have something different please let me know and I will help you find the correct kit.
Please note that the lift kit cannot be used if the Torflex axle has 3" high profile... view full answer...
Based on the pictures you provided it looks like you have an older Ventline manual vent with a fan so the Ventline E-Z Lift Ventadome Trailer Roof Vent w/ 12V Fan # V3094-601-00 you were looking at would just be the newest version and would make a great replacement if you're happy with a manual vent over a powered one.
To replace your current vent you'll need to scrape off the old sealant first. I recommend using a composite tool like # PT73HJ and really taking your time so that you don't... view full answer...
The # PF281007 Replacement Spray Head for Phoenix Faucets Hybrid Pull Out Kitchen Faucets is made for a Phoenix faucet and will not fit on the Dehco. Dehco does not have repair kits or replacement parts for their faucets.
I recommend replacing the faucet entirely. Since you were already looking at the replacement spray head for the # PF231441 Phoenix Faucets Hybrid RV Kitchen Faucet w/ Pull Out Spout, I believe this will work well for you. It has a plastic underbody, metal powder coated... view full answer...
Go To Results