Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Cold weather can make starting your diesel engine harder. This 1,000W threaded immersion heater screws into a 3/4" NPT opening to warm the coolant before startup, making starts easier, reducing engine wear, and bringing cab heat sooner.
Features:
Specs:
Notes:
Start your engine easier and warm your cab faster in cold weather with this frost-plug-style engine block heater. Heating your engine coolant keeps it from thickening and freezing, resulting in more reliable start-ups and smoother operation altogether. It also lessens the workload and extends the life of your vehicle's battery. And because starting your engine when it's warm creates less condensation in the engine block than starting it when it's cold, your engine will get better initial fuel vaporization, which causes fewer emissions and less pollution.
This frost-plug heater replaces the core plug in your engine block. The power cord on the heater is removable so that you won't need to buy a whole new heater if the cord gets damaged. The cord can be routed through your grille for easy access to a 120-volt outlet or extension cord. If needed, a longer or shorter cord (sold separately) can be purchased to better fit your application. Make sure the heating element is fully submerged in the coolant before plugging it in.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey everyone, I'm Ellen here @etrailer.com and we're going to be taking a quick look at the Kat's Heaters Custom Diesel Engine Frost Plug. So by having one of these in place, it's a very handy thing to have in cold areas where it has really, really low temperatures, because typically when you go to start your engine, it doesn't even want to start. It can also cause some damage if you start it during really cold temperatures because the lubricant inside there is not really moving around yet. So by being able to heat it up before we start the engine, it gets everything lubricated, it gets everything moving a little bit easier, and helps to extend the life of your engine overall.So let's take a closer look at it and make sure that this is going to be the right fit for you. It is going to fit into a 120 AC plug, so it's just your typical wall outlet at your house and we'll have about six feet of cord. That's going to connect into our actual frost plug.
This is a three-quarter inch NTP, threaded, or fitting here, so that should be the same size as what you're trying to thread into, and you can remove that bolt to make it a little easier to get that in place. Does have some lubricant on there, so that just helps it to thread down on our unit.On the other side, we'll have our plug and that can also be removed. So if you turn this jam nut to loosen that up, you can take this piece off so you can unplug it and actually drive around without having that cord hanging out of your engine. So that's how you can unplug it and plug it back in. It makes a little easier to keep things tidy.
Of course, you do want to be sure to unplug it before you start your engine. You don't want this going when your engine is on or you start that ignition, so it's one thing to keep in mind.This is rated for 1,000 Watts, the amperage is 8.3 amps. It is made in the USA and covered by a one-year limited warranty. As far as the size or the length of that frost plug going in there, it's about three and a half inches long. Going from the base of the threads is about two and a quarter inch.
Flip that around the other way so you can actually see it for yourself. So about two and three quarter inches there, or about three and a half if we go to the end of that nut. That does adjust a little bit from where this is actually, so let me take this off again.So the filament just by itself, about four inches or about four and three quarter inches. Just to give you an idea of how far in that's going to go. Another note with this is that you do not want to use the heater with a 100% antifreeze solution.
It's just not a good combo. That's going to do it for our look at the Kat's Heaters Custom Fit Diesel Engine Block Heater. I hope this has been helpful in deciding if this is going to be the right fit for you. We do have a lot of other options available here @etrailer.com, thanks for watching.
Ratings & Reviews

Katrina D.
2/3/2024
I am sorry that you were unable to get the help that you needed. Let me get you over to customer service again. Since Kats wasn't as helpful as you were needing, lets see if we can help.

Mark
12/21/2024
I purchased 2. I have already had to replace both.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.







Alexander
1/30/2023
Didnt even last a year and when you think about how little its used not a great track record, pretty disappointing