Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you want to protect your boat, load, and nearby drivers from rocks and rain spray, these 72" tandem-axle fenders help keep road debris from flying and hitting others or landing on your cargo. Weld them on or bolt with brackets.
When replacing your trailer fender, do your best to match the dimensions of the new fender to your old one. If your fender was damaged in a blowout, you can use the opposite fender to get the right measurements. Before you get started, always chock your wheels for safety. If you are installing a bolt-on fender, use your existing mounting hardware if possible, but be prepared to replace any bolts or screws that are stripped or rusted. If you need to remove an old, welded-on fender, you can carefully chisel it off yourself or take your trailer to a weld shop for professional removal. Do not forget to prime and paint the new fender to prevent rust and match your trailer's finish. Before drilling any holes, position the fender exactly where you want it and center it over your wheel well, marking your spots carefully. Measure twice and drill once. Finally, wait to fully tighten down the mounting hardware until you are sure the fender is mounted just right.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody, Andy here with etrailer.com. Let's take a real quick look at this tandem axle fender. Now, I only have one here on my table because of space limitations, but you will get two. And these rounded fenders are going to cover two of your tires on each side of your tandem axle trailer. Obviously, they're going to help block road debris from hitting other vehicles and helping to protect the cargo on your trailer. Now, looking at some measurements here, let me line this back up here for you.
Looking at the overall length from end to end, we're going to be sitting right at 72 inches long. The overall width is going to be 10 inches wide. And then the height of the fender itself is going to be right at about 20-1/2 inches tall. Each fender is going to weigh about 11 pounds. And so these are going to come as you see it.
It's going to come ready to be primed and painted for corrosion protection, and of course, to match the finish of your trailer as well. So, this is going to basically come to you raw with a slight oily film on it. So you just want to make sure that you clean that off and then prime it and paint it to make sure that this isn't going to rust out on you. This is going to be a weld-on or a bolt-on installation. Of course, you probably know you don't want to use the backing plate to mount the fender to your trailer.
This does require drilling and the purchase of a, a fabrication purchase, or a fabrication rather, of mounting brackets. So, none of that is going to be included with these fenders, you're simply going to get these two fenders. And you want to do your best to match the dimensions of your new fender as well to the old ones. So, if for whatever reason, maybe a fender was damaged during a blowout or something like that, you do want to use the opposite fender, the one that's not damaged, to get the correct dimensions if you're not sure of the dimensions of fenders that you need. So again, you will get two, and if you do pick this up, we would love to hear back from you regarding how the installation went and how they're working out for you.
So you can share your experience with us by dropping a comment or leaving a review on this product page. And if you happen to have any other additional questions, don't hesitate to reach back out to us. We do want to make sure that you're getting exactly what you want and need. Well, I think that's going to wrap up our quick look today. I do hope that it was helpful for you. Again, my name is Andy, thank you for joining me.
Great fenders for the price, well made and fit my trailer perfectly, only issue I had was there is minor surface rust on both, I don’t see it being an issue but felt I should mention.
Fenders are exactly as described and seem like good quality
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Nick S.
12/22/2025
That looks great on the trailer! I am glad they fit well for you. What are you using that trailer for?