To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
A lot of covers make you pick between protection and convenience. The Sentry gives you both. Its 3/4" thick aluminum slats are wrapped in high-grade vinyl so you get the security of a hard cover with the flexibility of a soft roll-up. When you need your full bed, just pull a release cable at the tailgate and roll it up in seconds. Safety straps at the cab hold it in place, and the compact roll stays low so it won’t block your rear window.
This cover isn’t just tough—it’s built for the long haul. The 5-layer polyester and vinyl surface is bonded to black aluminum slats that resist dents and impacts. The material is tested to withstand temperatures from -40°F to 120°F and is resistant to UV rays, dirt, and moisture. Whether it’s beating sun, heavy rain, or snow, the fabric keeps its clean, matte finish and protects your gear from the elements.
For anyone who wants their truck to look clean and aerodynamic, the Sentry sits just 1/2" above the bed rails thanks to 15-degree-angled side rails. That subtle slope reduces wind drag and noise while giving the cover a sleek, flush look. Because it mounts inside the bed rails, you still have access to stake pockets for tie-down anchors or racks.
Keeping your gear safe doesn’t have to be complicated. The Sentry uses slam latches at the tailgate and automatic security latches at the mid-bed. When you close the cover and lock your tailgate, the bed is fully secured—no extra steps. The hard aluminum slats can’t be cut open like soft covers, so you get real protection for tools, equipment, and valuables.
Getting the cover lined up right the first time is easy. The clamp-on side rails bolt to the inside of your bed rails without drilling. Built-in lips keep the rails square as you tighten the clamps, so the cover rolls evenly every time. Quick-release guides let you remove the cover completely in seconds—no tools needed. And with a 400-lb evenly distributed weight capacity, it’s tough enough for work or weekend use without slowing you down.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Allan
5/17/2025
Cover is holding up great. Gets everything dry in the bed of my truck. If you are thinking of buying one, just do it. Great product