See what our Experts say about this Inno Roof Rack

• Recommended Roof Rack System for a Yakima SkyRise HD Tent on my 2016 Lexus GX 460
  I recommend using a rack system like the Inno system which consist the Inno Aero Crossbars part # INXB93-100, the Inno Flush Feet for Aero Crossbars part # INXS300 and the Custom Fit Kit for Inno Roof Rack Feet part # INTR152. The reason we can use tents like the Yakima SkyRise HD Tent for Roof Rack Crossbars part # Y07436 is because the weight ratings are for a moving load when the vehicle is parked they rate the rack a bit higher allowing us to get up to the capacity of the tent. The...
  view full answer...
• Recommended Roof Rack for 2016 Lexus NX 200T with Flush Mounted Rails
  We do offer a wide array of roof racks that are confirmed to fit the 2016 Lexus 200T vehicles. The only model I could find that has the flush mounted rails like you mentioned in your question is the NX 200T. If this is your model Lexus, the most cost-efficient crossbars and fit kit we currently have available is the Inno Aero Bar Roof Rack, which consists of parts # INXB93-100 for the two aero crossbars (front crossbar is 36 inches and rear cross bar is 39 inches), # INXS400 for the Flush...
  view full answer...
• Will Inno Square Bar Roof Rack Fit A 2018 Mercedes GLA45 AMG
  Yes, the Inno Square Crossbar Kit including parts # INB117, # INXP, and # INTR162 are a confirmed fit for your 2018 Mercedes GLA45 AMG. We can't recommend using duct tape between the mounting feet and your factory rails. The rack was designed to fit to the factory flush mounted rails so an additional material between the two could affect it's hold and reliability. These feet are designed to fit without scratch or damage so you can feel good about this solution. I have also included...
  view full answer...
• What Flush Crossbar System do You Recommend for My 2022 Mercedes GLC SUV with Flush Rails?
  From my available specs on your 2022 Mercedes GLC SUV, you have flush mounted factory rails on your roof. For a great flush roof rack system of crossbars that don't extend past the roof rails, there is one that fits your vehicle style. For that route, I recommend the following setup: - Inno Aero Crossbars - Aluminum - Black - 36" Long and 39" Long # INXB93-100 - Inno Flush Feet for Aero Crossbars - Flush Side Rails # INXS400 - Custom Fit Kit for Inno XS300, XS350, XS400, XS450, INTR,...
  view full answer...
• Roof Rack and Cargo Basket for 2016 Lexus GX 460 to Carry Cargo Bag
  Your best solution is going to be to install a roof rack on your 2016 Lexus GX 460 like the Inno part numbers # INXB93-100, # INXS300, and # INTR152 so that you can then mount a basket to the bars like the Thule Canyon XT # TH859XT and easily carry your cargo bag.
  view full answer...
• Thule Flush Roof Rack For a 2017 Lexus RX350 with Factory Flush Rails
  I do have Thule options for a 2017 Lexus RX 350 with flush rails but the Thule AeroBlade Edge is an old system that we no longer carry the correct fit kits for. Instead, I recommend the Thule WingBar Evo Crossbar part # TH711220, part # TH710601,and part # TH186044 which has the updated design. I know this system doesn't have the flush bar style you were after but they don' stick out much further at all and they allow for more items to be carrier. It can also be easier removed when not...
  view full answer...
• What Crossbar System do You Recommend that Doesnt Extend Past the Feet on My 2018 BMW X1?
  I have a great flush crossbar system for you. Unfortunately, I confirmed with Thule that they discontinued the Fit Kit 4023 which is required to mount the AeroBlades TH7602B-TH7603B to your 2018 BMW X1. Without that fit kit, there is no way to attach the AeroBlades to your flush rails. We also do not have any other Thule systems that do not extend past the feet that fit your flush rails. With that being said, the only other option for a crossbar system for your X1 that does not extend...
  view full answer...
• 2021 BMW X3 Inno Roof Rack Options for Flush Factory Rails
  Yes, there are Inno roof rack fits for the flush rails on your 2021 BMW X3. I prefer the crossbars that overhang the legs instead of ending in them because you get more real-estate to work with but there is something to be said for the sporty look the latter offers. Below are the parts needed for either roof rack style for your vehicle. Flush Feet Style (Sporty) 42" Aero Crossbars - # INXB108-2 Flush Feet - # INXS400 Fit Kit - # INTR140 Through Feet Style (Standard) 54" Aero Crossbars...
  view full answer...
• Is the Custom Fit Kit for Inno IN93FR the Same as the TR183 for an Inno Rack on a 2020 Ford Edge
  I will start with the good news, the Custom Fit Kit for Inno # IN93FR is the TR183. The TR183 is the manufacturers part number and the IN93FR is our number for the same TR183. From there you will use the Inno Through Feet for Aero Crossbars # INXS450 for either the Inno Aero Crossbars # INXB123-130 (48" & 51") or # INXB130-138 (51" & 54"), the difference is the length of crossbars. The third option you mentioned use the Inno Flush Feet for Aero Crossbars # INXS400 and the Inno Aero Crossbars...
  view full answer...
• Recommended Roof Rack and SUP Carrier for a 2015 Mini Cooper Countryman
  Yes Nathan it would be possible, and you could use the Custom Fit Kit for Inno XS300, XS350, XS400, XS450, INTR, and INXR Roof Rack Feet # INTR142, Inno Flush Feet for Aero Crossbars # INXS400, and the Inno Aero Crossbars # INXB93-2 you're looking at. From here you can use a SUP carrier like the Thule SUP Shuttle Stand-Up Paddleboard Carrier with Tie-Downs # TH811XT which can carry up to 2 SUPs that are 34" wide.
  view full answer...
• Custom Fit Low Profile Roof Rack System For A 2016 BMW X5
  I have the perfect roof rack for your 2016 BMW X5 that matches all the requirements you have specified. For a roof rack with aero crossbars and no overhang, you will want the Inno Aero Crossbars part # INXB108-2, part # INXS400, and part # INTR140. The Inno Aero Roof Rack System is a direct fit for your vehicle and the cross bars that mount to the vehicle's side rails are placed into the end caps on the foot pack included with this kit. This will in turn position the crossbar ends directly...
  view full answer...
• Will A Roof Rack On My 2019 BMW X3 Interfere With My Sunroof Operation
  Any aftermarket roof rack you purchase for your 2019 BMW X3 with flush rails may have issues with interference between the roof rack and the sunroof. In fact, this interference is mentioned in all roof rack instruction manuals. My recommendation for customers who want to know if there will be interference is to put your front crossbar and tower/feet/legs together and place it on the roof in the correct position. Do not install it, just put it in place on the roof. Then CAREFULLY open your...
  view full answer...
• Roof Rack Recommendation for a 2015 Audi Q7
  It looks like the 184002 fit kit from Thule has been discontinued so while the Thule AeroBlade Edge # TH7602-TH7602 is still a valid part, this means that we will need to go a different direction for your 2015 Audi Q7. I recommend going with the Thule WingBar system because it is the upgrade to the AeroBlade Edge, but if you're more concerned about a roof rack that has crossbars that end in the legs then you'll need to go with the Inno roof rack instead. I will list both options below...
  view full answer...
• Recommended Roof Rack for 2016 Lexus NX 200T with Flush Mounted Rails
  We do offer a wide array of roof racks that are confirmed to fit the 2016 Lexus 200T vehicles. The only model I could find that has the flush mounted rails like you mentioned in your question is the NX 200T. If this is your model Lexus, the most cost-efficient crossbars and fit kit we currently have available is the Inno Aero Bar Roof Rack, which consists of parts # INXB93-100 for the two aero crossbars (front crossbar is 36 inches and rear cross bar is 39 inches), # INXS400 for the Flush...
  view full answer...
• Will Inno Square Bar Roof Rack Fit A 2018 Mercedes GLA45 AMG
  Yes, the Inno Square Crossbar Kit including parts # INB117, # INXP, and # INTR162 are a confirmed fit for your 2018 Mercedes GLA45 AMG. We can't recommend using duct tape between the mounting feet and your factory rails. The rack was designed to fit to the factory flush mounted rails so an additional material between the two could affect it's hold and reliability. These feet are designed to fit without scratch or damage so you can feel good about this solution. I have also included...
  view full answer...
• Available Inno Roof Rack Fits for 2018 Honda HR-V with Flush Roof Rails
  We offer three roof rack systems from Inno that fit the 2018 Honda HR-V with flush mount roof rails. Please note that none of these are square bar racks; all use Inno's Aero crossbars, which for your vehicle are available in three bar lengths. You can see all of these on the linked page. With these racks you have a choice of a flush fit for the Aero crossbars with the rack feet or to have longer bars that extend out past the rack feet. The flush system uses 39-inch bars and consists of...
  view full answer...
• Flush Mounted Roof Rack for 2018 Audi Q5
  Roof racks are custom fits for vehicles, and the Thule rack you mentioned is an entire kit and won't fit on your 2018 Audi Q5, although there is a rack with the same style which does. So long as you have flush-mounted rails there is a rack from Inno which has crossbars match the width of your Audi's roof: - Inno Aero Crossbars # INXB100-108 - Inno Flush Feet for Aero Crossbars - Flush Side Rails # INXS400 - Custom Fit Kit for Inno # INTR138 For a Thule roof rack, they have a style where...
  view full answer...
• What Flush Crossbar System do You Recommend for My 2022 Mercedes GLC SUV with Flush Rails?
  From my available specs on your 2022 Mercedes GLC SUV, you have flush mounted factory rails on your roof. For a great flush roof rack system of crossbars that don't extend past the roof rails, there is one that fits your vehicle style. For that route, I recommend the following setup: - Inno Aero Crossbars - Aluminum - Black - 36" Long and 39" Long # INXB93-100 - Inno Flush Feet for Aero Crossbars - Flush Side Rails # INXS400 - Custom Fit Kit for Inno XS300, XS350, XS400, XS450, INTR,...
  view full answer...
• Is The Sportsrack J-Style Kayak Carrier SR5511 Compatible With 2010 Santa Fe Roof Rack?
  The SportRack Kayak Carrier with Tie-Downs - J-Style # SR5511 will fit your 2010 Hyundai Santa Fe if it has the factory crossbars running left to right across your roof. If your vehicle just has the factory side rails running front to back then you will first need to install a crossbar setup such as Inno Aero Crossbars # INXB100-108 with the necessary Feet # INXS400 and Fit Kit # INTR166. I attached a couple demonstration videos for you.
  view full answer...
• Will Rhino Rack Components Fit 2018 Mercedes Benz GLA Class
  Thank you for your picture. The Inno Roof Rack Kit # INB117, # INXP, # INTR162 definitely fits your 2018 MB GLA250. It looks like you have the Rhino-Rack Nautic Roof Kayak Carrier w/ Tie-Downs # RR570 which are compatible with square bars like this Inno rack. The # INB117 dimensions are 46" long x 7/8" tall x 1-1/4" wide and the maximum crossbar dimensions for the Rhino Rack Carrier is 3-7/8" wide x 1-3/8" tall. You'll need a minimum crossbar spread of 23-9/16" for these Rhino Rack...
  view full answer...
  
• Parts Needed to Install 65 inch Inno Square Bar Roof Rack on 2025 Mazda CX-50
  Hey Lorraine, what you'd need is the foot kit part # INTR with the fit kit part # INTR162 and you'd be able to use the Inno Square bars # INB165 on the roof of your 2025 Mazda CX-50! How did you like the Inno rack?
  view full answer...
• Inno Roof Rack that Fits 2018 Mercedes Benz GLA 250
  To install an Inno square bar roof rack on your 2018 Mercedes Benz GLA 250 the correct components are part numbers # INB117, # INXP, and # INTR162 which does attach to the flush rails on the roof of your vehicle. Then you could install the Inno Gravity Ski Carrier part # INA951 for a 6 ski rack or part # INA952 for 3 skis.
  view full answer...
• Will the Malone DownLoader Fit Inno Aero Crossbars on My 2020 Mercedes GLA 250?
  All of the crossbar sizes of the Inno Aero crossbars that we have listed as confirm fits for your 2020 Mercedes-Benz GLA 250 are the available size options that Inno has for you based on your crossbar length needs for the vehicle. Depending on what accessories/cargo you need to transport, you can use more or less crossbar space. The length does determine how long the crossbars stick out past the feet. If you are planning on transporting a kayak, I recommend the longer roof rack bar system...
  view full answer...
• Will Inno Square Bar Roof Rack Fit A 2018 Mercedes GLA45 AMG
  Yes, the Inno Square Crossbar Kit including parts # INB117, # INXP, and # INTR162 are a confirmed fit for your 2018 Mercedes GLA45 AMG. We can't recommend using duct tape between the mounting feet and your factory rails. The rack was designed to fit to the factory flush mounted rails so an additional material between the two could affect it's hold and reliability. These feet are designed to fit without scratch or damage so you can feel good about this solution. I have also included...
  view full answer...

Do you have a question about this Roof Rack?