# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!
Primarily bought the front receiver hitch to haul our 2 e-bikes. Did that because it was easier than hauling them inside our camper. And didn’t trust them bouncing around on the back bumper of the camper. Hauled the bikes that way on several camping trips. Easy as pie and I could keep an eye on them the whole trip.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2022 TRD Pro fits snugly. To keep the OEM skid plate, you can remove the skid plate’s 2x front spacers and spacer washer locks. Removing this will allow you to fasten the front 2x M10 oem bolts. The 2x rear M10 bolts will need to be replaced with 2x smaller length M10 bolts that are at half the size of the oem bolts. My local hardware store had plenty of options.
This is the second hitch for my Toyota 4runner The first one you sent me was wrong. The box came in with had holes in it. Today I received the correct hitch. I’m assuming the correct hitch I haven’t had it installed yet I hope it’s the right one, but it came in the box, and it was all tore up. both ends of the hitch are sticking out of the box of the new one I just received. That’s pretty much the same condition that I got the other one. I’ve ordered hitches parts from you for years never have I never gotten product that was sticking out of the box. Unacceptable. I just hope it fits.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I have had the front receiver hitch installed on my 1996 Suburban for about a year now. I have a 12000 lb winch installed using that receiver hitch. I have gotten stuck twice and had to use the winch to extract the truck. Very glad that I have the front receiver hitch as it made putting on the winch very easy. Also useful for mounting a receiver mount bicycle rack to the front as well.
Product was shipped promptly and arrived a few days later. Packing was good for a heavy item with pointy edges, no issues breaking out of the box. Installation on a lift took about 30 minutes on my 1999 K2500 Suburban. The bolts were long enough to allow for my tow hooks that were already in place. A bolt stringer to pull the rear bolts from the top (inside the frame) is provided along with nuts, the other four just replaced the stock bolts that I had that mount from the bottom into tapped frame metal through the tow hooks. Curt makes great quality stuff. Clearance was reduced a little but I'm not concerned about it.
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
Product shipped and received on time. I'm very happy with the packaging. Hardware was included with instructions to install the hitches I purchased.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.
Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Dealing with etrailer.com was definitely easy. They very much so appreciate any and all business. Shipping was pretty quick and they kept me informed on my order status all the way through as well with follow up to make sure everything was satisfactory. I have a 2019 TRD Pro Tacoma, I opted to just replace my skid plate with a lighter one given the slight addition weight of the hitch. On top of the fact I didn’t want to have to cut such a pricey factory part. Everything installed easily and while I’ve never had much reason to use fish wires I can tell you in this situation it’s a lifesaver. If I recall some people had issues fitting a ratchet to the top nuts. I used my stubby bolt through ratchet set and worked pretty flawlessly. Got to say over all I have zero complaints, some people mentioned the loss of ground clearance and/or approach angle but it’s really not that intrusive. I would definitely recommend this to anyone looking to make their Tacoma a little more versatile. My main objective was to be able to use my Surf Mate hitch rod/cooler set up without it getting in the way of the tailgate. Everything works great!
Well engineered product. Less than 30 min to install on my 2022 TRD Off-road. No trimming at all on TRD Off Road model. It looks a little utilitarian up close, but not so much from a distance. My cycle jack worked perfectly for this task. BTW.. The fish wires are a stroke of genius.
# 9
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very easy to install. works great for bike rack and generator box.
After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .
# 10
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Overall I love the front hitch and it's fit on my 2017 RAM 3500. There's been some reviews talking about the packaging and also about the installation, so here's my experience. The box was sturdy and was shipped via UPS. It arrives undamaged. There was some extra carboard added across the top of the box presumably to help protect the receiver. When I opened the box I noticed that one of the brackets was slightly bent. I thought this may have happened during shipping, so I placed the receiver in my bench vice and gently brought it back to square. DON'T DO THIS. It appears the slight bend in the bracket is intentional. The receivers fits very snugly to the truck frame so that bend it to make installation easier. When I tried to install the receiver it was so tight I could not get it up into the truck frame. I ended up bending it back out of square (about 1/4" on each side). After I re-bent the brackets slightly it fit great. When you torque down the blots the brackets come back to square and everything was perfect. My only minor criticism is with the instructions tell you to cut out a portion of the lower plastic deflector on your truck. The instructions tell you to cut a piece that is 4/25" wide. It doesn't need to be that wide for this truck - it could have been the same width as the 2" receiver. It's not a huge deal, but if you want a really tight fit on your deflector, then just cut it smaller. The whole process, including the extra unnecessary bracket bending, took me about 2 hours to complete on my own. I used jack stands to support the bracket during the install, but an extra pair of hands would have made the process much quicker.
Seems nice and solid, should be strong enough to haul my 425lb motorcycle + 60lb carrier. Based on some of the reviews about what a pain it was to install I decided not to mess with it and take it to a hitch shop. They confirmed some of the complaints I read here so it was money well spent.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."