# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Sara R was helpful helping me find the right hitch for what I described as needing. I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression. Overall, excellent customer service and product.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 3
Draw-Tite Drawbar for 1-1/4" Hitches - 4-3/4" Drop - 7-1/2" Long - 3,500 lbs
Exactly what I needed. I bought this Mercury Mariner used and it had factory installed hitch with a 1 1/4 receiver. I needed a drawbar with a substantial drop to tow my utility trailer somewhat level. Local shops had lots of 2 inch drawbars with drops but no 1 1/4 and I was even told that they weren't made and I would have to use a 1 1/4-2 inch receiver adapter do get what I wanted. You folks had what I needed and it arrived quickly. I should have looked here first.
I have a 2012 Outback. The car has more ground clearance than my previous Outback so the 2 1/2" drop on my old drawbar resulted in the rails on my motorcycle trailer tilting backwards slightly. This made loading the motorcycle a bit tricky because it wanted to roll backwards when loaded, until strapped down. I looked all over town for a drawbar with more drop but was unable to find one. Finally found this drawbar and it worked perfectly with enough drop to level the rails on the trailer. I also like the fact that it is a bit shorter than other drawbars and doesn't stick out as far.
# 4
Draw-Tite Ball Mount for 2" Hitch - 7" Rise, 8" Drop - 9-1/2" Long - 12,000 lbs
Heavy Duty Drop Down Hitch no problem pulling a 10,000# trailer
It fits perfect on my f350 diesel, super heavy duty. I'll be using it for towing my car tilt bed trailer.
# 5
Draw-Tite Ball Mount for 2" Hitches - 3" Rise, 4" Drop - 12" Long - 12,000 lbs
Solid pc of towing equipment!
Still performing excellently after a year. This draw bar is much stronger than we even need, but it gave us the two extra inches of length needed to clear the bumper, so we could install the Curt hitch-mounted clamp-on bike rack, also purchased here & working well.
# 6
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 12" Long - 5,000 lbs
The Ball Mount was noisy upon hitting bumps, uneven road, etc. I have since gone to a shorter, dampened ball mount but I have to remove the spare tire when I use it!!! Ruben
The receiver is exactly what I was looking for. Put it on a 2016 chevy traverse and it is the right length for pulling a trailer. Looked at 6 1/2 inch, too short. Quality is good also. I give it 4 stars.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."