Most Popular Single Axle for 2019 Mazda CX-5

Bought this to replace the shackle links and hardware for an existing aluminum trailer, did not use the brackets. Bolt shafts are "flared" on the inside head end so you need a press to push them into the bracket. Otherwise, you need to crank down the nuts as you install them to seat the bolts properly.

Good kit with the necessary parts to replace leaf spring suspension. I welded the hangers rather than bolting them. The parts are not coated for the price point so you will need to paint them or they will rust immediately.

Click to Enlarge

Click to Enlarge

My 6' x 10' landscape trailer was a homemade by a prior owner. While it was mostly constructed very well, the spring hangers were not correct. The spacing for the springs was also wrong, and it had very little fender clearance. There was also evidence that the spring U-bolts had contacted the frame on occasion. (I do not carry loads anywhere near the 3500# axle rating.) I added an extra set of holes on the front hangers in case the ride height proved to be too much, but I like the way it sits with the stock holes. I don't think I'll be utilizing the extra holes. This kit was just the ticket to increase the suspension travel and fender clearance on my landscape trailer. Now it "sits right"!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I am sorry but I can not remember names but I talked with two very helpful ladies and could not have been happier with their assistance. Thanks again, the trailer build is going great.

This is a great kit! It included everything we needed to replace the old, worn-out brackets on our 6'x10' trailer. The directions were helpful and the brackets and hardware are nice and solid. We've had zero issues with the leaf springs (purchased on etrailer.com, also) or the brackets. Would definitely recommend!

Excellent, had everything I needed and more for my trailer. Everything fit well!

Click to Enlarge

Click to Enlarge

Awesome product, awesome smooth, awesome load handling. So awesome I'm back ordering jounce-spring helpers from Timbren for my truck. Item # TGMR15MR

Click to Enlarge

Works great. Love them. Everything went perfect showed up on time instructions were great. Couldn’t been better

It seems to stabilize the trailer a lot better than the factory equipment. Less side to side movement and it seems that inside contents are not as bounced around as before.

I made some brackets to bolt to the frame. Now I have 100% contact with the Sumo Springs. The are working extremely well!

Click to Enlarge

Great kit! Installed this on my 1995 Jayco Fifth Wheel and it really improved the ride height with my truck. It’s been on 2 round trips from Texas to Montana since and many other trips locally with no issues.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Our trailer was so low...that it could not make it up a low curb and some driveways - especially when fully loaded. Went with the Dexter axle flip kit. The Dexter bracket and base plate pieces are worth the extra $20-$30 compared to other similar kits - they make fitment easier, eliminate any guesswork on placement, and decrease installation time because of it. Took 2-3 relaxed pace hours for us to do single axle install. Tools required were ratchet/wrench set (13/16 deep socket worked for us for most of the bolts), cheater bar (for working those rusty bolts off), drill, angle grinder (cutter disc for oem u-bolts and leaf spring bolts that are rusted or welded in place, stripper disc for cleaning area around new bracket for welding) welder, floor jack and jack stands. We had to remove the leaf springs, as the wheel mount brackets would not fit through the openings. Was hoping we wouldn’t have to, but it was pretty simple to do. We jacked the trailer up. Removed the wheels. Removed the axle. Cleaned the axle area where new brackets go. Set the height and placement of the new Dexter brackets. We left the OEM brackets on the axle and placed the Dexter ones in the exact same position 180 degrees on the other side. Welded them on. Reinstalled leaf springs. Reinstalled axle, reinstalled wheels. Then voila! We added 6 full inches of height. Super awesome.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Product is as described, installation was easy & performed as expected.

Click to Enlarge

I ordered these to help reduce the rolling (tilting) of my 18' travel trailer that I use off-road. Also, I am hoping it will absorb some of the shock. I have added some photos of before and after installation. The installation was simple, I used 5/16" sheet metal screws instead of the bolts supplied. Time will tell if they work as expected. As you can see from the photos, I have previously added an Etrailers shock mount kit to my axle. I made custom lower mounts that I welded to the axle and used the supplied upper mounts.