Most Popular 4500 lbs GTW for 2018 Ford Explorer

I installed this hitch with the vehicle on the ground. I did not use any jacks. I am giving this 3 stars because of the difficulty installing rubber exhaust hangers to the hitch. I could have done this installation by my self. Except for the misery of trying to bolt the exhaust hangers to the hitch. The use of a carriage bolts was a miss by the designers of this hitch. I had to wait for a friend to help me. Because of this I had to finish in the dark. Looks great

Great product with the price of litle over 100$, took me 45 minute to install in my garage. I follow video instruction provided w/o any problem (i had mechanic background).

Excellent product. and great service from etrailer . Shipping was very quick and price was right.

This is a nice, heavy duty hitch. Probably heavier duty than the 2011 Rav4 I put it on, but I like the 2" size reciever for the flexibility. You can always adapt down, but going up can be tricky. It was about a 20 minute install with about 40 minuets of up and down looking for a tool. Mine dod not have the bolt on muffler hanger the instructions referenced, but that was just a couple of bolts I didn't have to worry about. One trick I have learned with installing hitches on the ground by yourself is to use a jack to hold it up and in place while you start the bolts. The other is to run the bolts into the holes before you get the hitch into position. If the hole wasn't use, it ca be full of grit and road grime and it is a lot easier to deal with it before you have an 80 pound hitch hovering over you head. As always, eTrailer was a great source. I think this is the seventh hitch I have bought and installed from them over the years. I still the they need to include an "I got hitched at eTrailer" bumper sticker with every purchase, but I suppose solid service and affordable pricing is good enough.

I bought the Draw-Tite for a 2018 Ford Edge Sport. I saw lots of discussion about throwing out the heat shield, which left the rear bumper flimsy. I was able to trim the heat shield, reinstall it, which firmed up the rear bumper cover. Attached are some pics showing how this was done. Basically, trim off the ends and center piece, anything that would extend back towards the hitch. I used a Dremel cut off wheel and Tin snips, worked great. Then, cut a 3 inch square next to the centerpiece opening. Do not cut the heat shield material. This allows the receiver part of the hitch to fit in the opening. Then, trim the ends by following the heat shield material. Slide the heat shield back in place starting from one end and pushing it across and back into place. Reattach all bumper cover bolts, that will firm up the bumper cover. Pull wires worked great. I used jack stands to hold the hitch in place and installed it myself. Just watch the video a couple of times, it was not that hard. I bought the Curt wiring harness as I wanted to keep the pigtail inside when not using, which will be about 95% of the time. Good product, easy install.

The install went easier than expected. 3 Hours start to finish by myself. There were a few bare edges where paint was removed during shipping, which will be the first to rust. I might try to touch it up but in past experience this doesn't help much. Adding some padding on the edges of the frame might prevent damage during shipment. To the install. I am a moderately skilled shade-tree mechanic, and anyone who can do minor car repairs should be able to tackle this install. Removing the trim was easy. Using a strap to lower the muffler was not too bad (even detaching the hangers wasn't too bad). I would definitely go this route instead of removing the bumper cover as some others have mentioned... much easier. The hardest part was getting the hitch frame in place without a helper. I ended up using some landscaping bricks and an old empty car battery to lay one end of the frame on while I attached the other. Having someone to hold one side while you attach the other would make this part MUCH easier. Still, I was able to tackle it without too much trouble. Note the frame IS heavy, so you won't be able to just hold it up while you get the bolts attached. After that, I tightened the bolts, re-hung the muffler, and put the trim back on and it looks and works great! Now I can go fishing again with my new Edge. Also of note, the backup camera and the automatic rear hatch sensor still work fine. You do have to "kick" to just one side of the hitch or the other... but it works no differently than before. Very satisfied with the product, as long as it lasts the life of the car without rusting to pieces... which time will tell on that front.