# 1
Roadmaster InvisiBrake Flat Tow Brake System - Preset
Read the instructions and only use the trailer video/s as a guid!! Install was tough but doable. Take your time if you want a clean install. Lastly, the kit comes with updated check valves. The video will tell you that the "red side" faces the engine. That's not true if you are using the "black side" check valve. The black side faces the engine while the red is opposite. I wasted several hours troubleshooting a stiff break pedal when in reality, I had the check valve installed just as the trailer video explains it. My bust for trusting the video and not reading the install instructions fully.
The braking system and the lights are working, one year after I bought them. However, I am towing a 2016 Keep Patriot, and about 2_500 miles after install, the system started making an annoying clicking noise when I enter the Patriot, which stops after about 10 seconds and then starts up again, usually a minute or so later, for another 10 or 15 seconds. etrailer first said that they had never heard of.such a thing, then said that there are otherwise comments for Keep Patriot owners on forums. Still have no.fix. Also, at first I did not know that to store the tow bar, it must be pulled up so that the post fitting can moe to the position where it fits into the hole.in the smaii yellow bracket, which works well when used correctly. And store the coiled.wide in your tower vehicle.to prevent corrosion which will interfere with its function.
# 2
Demco Stay-IN-Play Duo Flat Tow Brake System for RVs w/ Hydraulic Brakes - Proportional
I mounted this in a 2014 Chevy Spark. Finding a spot for the main control unit was interesting, but I found a video for a 2017 Spark that I could use. I did have to drill an extra hole in the mounting flange and car. I haven't taken it on a trip as of this time, but a tow around the block indicated it was working. One note, watch about placing the LED indicator behind the tinted part of the toad window. It makes it harder to see from the camper camera.
I installed the Stay n play on a 2017 Jeep Cherokee Trailhawk. I pull it with a Diesel Sprinter, and braking control is very important to me. Previously I used a Brake Buddy. The Demco system is a world of difference. The proportional braking, simplicity of design, ease of engagement/disengagement, and reliability have provided an improved sense of confidence and security when flat towing. Installation was a challenge but is well described in instructions and videos.
# 3
Roadmaster BrakeMaster for RVs w/ Air or Air-Over-Hydraulic Brakes - Proportional
This kit was installed on a 2007 Jeep Patriot. It did require fabrication of a seat mount bracket. Fairly easy with some angle iron and some spacers. Install was fairly straightforward. It required mounting the surge tank inside the engine bay and running wiring to and from the battery and breakaway switch. It also required mounting the quick release air fittings at the bumper, inside the vehicle, and also at the rear of the RV. I also mounted the LED indicator inside the RV and utilized the existing towing harness to run power from the vehicle to the front of the RV.
The product shipped on time and has been worry free. etrailer gets 5 stars for customer service every time I order from them.
# 4
Roadmaster Even Brake Portable Flat Tow Brake System - Proportional
1996 Ford F-250 and F-350So I never used mine. This is for those trying to decide if they need one. I tow an F250 with a 43’ tag axle, with an 8.9l Cummings. Yes I can feel the truck back there but I have never had the need for additional braking. Crossing the Snoqualmie pass on I-90 or driving through the cascades, I have no problems slowing with the engine brake. I have a big rig and tow a big truck so if this is your set up I’d give it a shot before committing to such an expensive item that I never use. I’m sure smaller rigs pulling larger trucks will benefit from a device like this.
Ordering was easy. Delivered very promptly. Actually cheaper then what the manufacturer sells it for. Live near manufacturer and having them install all my flat towing components this month. Great service Etrailer!!
# 5
Brake Buddy Stealth Supplemental Braking System - Proportional
I am a proficient DIYer (and was an auto mechanic many years ago). The installation took a lot of time - perhaps 8-10 hours for the brake controller. The most special tool needed was a rotary cutter (e.g., a Dremel tool). A cordless impact driver was also very helpful, especially with the self tapping screws. Getting the pully in the perfect position under the brake pedal took some trial-and-error to get perfect. Also, the included bolts for the brake pedal bracket where too short to accommodate the width of the brake lever - easily remedied with slightly longer standard bolts. Be very mindful of what is on the other side of the sheet metal you are planning to drill into. The brake supplemental vacuum system was a bit of a challenge, as the instructions are very vague regarding how to mount, and the space I had to work with was surprisingly tight. I ended up creating a mount on the inside front fender, and bolting the pump to that. Also, tapping into the vacuum lines took a couple of tries to get a leak-free connection. Think ahead about this, and be prepared to get a few small parts like hose clamps or right-angle hose connectors. This would be a potential consideration for any vacuum boost added on any vacuum power-assist application with any controller. I mounted the Brakebuddy main unit under the rear seat - that was a perfect location, and much better than the often suggested location under the driver's seat. I was very pleased with the installation result. I paired this with a Nighthawk tow bar. Be warned that the tow bar's included cable will not be compatible with the Stealth, as the Brakebuddy uses a proprietary connection at the towed vehicle. The upside of this proprietary connector is that all connections are build in, including the brake away cable and the battery charging line. (I modified the Nighthawk by replacing the included cable with a 4-pin cable to power the lighting system on the bar. This is just for extra safety and cool looks - I could have just not used the tow bar's included cable). With 1,200 miles of towing behind us, I can say I am very pleased with the performance. I rarely notice any difference in braking effort or effectiveness - which is a big advantage for a proportional system. My favorite feature is the ease and speed of connecting or disconnecting the towed vehicle. I'd give this a 4.5 stars out of five if I could, because I did need to add a few parts and make a couple trips to the hardware store to complete the installation. However, the excellent performance and ease of use once installed more than makes up for the inconvenience during initial installation. Special appreciation to the people at eTrailer, especially Nicole T, who provided support and guidance from pre-sales to installation. Also, I called Brakebuddy's support line with a concern, and they immediately picked up the line, addressed my question, and offered to immediately ship any parts if needed.
I choose the Brake Buddy Stealth for my 2021 Jeep Wrangler because I wanted a “stay in place” brake system and felt it would be a clean looking installation. I finished the toad side of the installation today and thought I’d leave some notes on what turned out to be a bigger project than I’d anticipated. Again, this is my experience on the 2021 Jeep Wrangler 2-door. Your experience on other vehicles may vary. I started this install after installing a Demco Tabless Base Plate. Right out of the blocks, there’s really no convenient location to mount the cable connector to the Demco baseplate. I chose to mount it to under side of the bumper on the driver’s side. To provide clearance and a route for the wires, I had to cut a notch into the plastic air dam. I used one of the already screw screw holes and used self tapping screws in the other three locations. For added strength I epoxied the connector to the bumper as well. Since the bumper would be unremovable if the connector were hardwired, I added a waterproof connector. The kit is stingy with wire lengths, so I substituted my own wire. The Stealth unit itself i mounted beneath the driver’s seat. Don’t be fooled into believing there is clearance when testing with the driver’s seat positioned for rear seat access. Once the seat is returned to normal operation it lowers a bit and the box keeps the seat from being move forehand aft. I solved the problem by installing 5/8” thick nylon washers under the rear end of the seat slides. I also cut away a bit of the carpet under the front, inboard corner of the box. You will need to remove the driver’s seat in order to attach the front screws of the box. Be sure to disconnect and isolate the neutral battery terminals to prevent inadvertent air bag discharge. After removing the interior trim from the A-pillar, the door sill, and the driver side foot well, The wiring and cable tucked nicely away along with the OEM wiring and wiring for my taillights. I mounted the pulley horizontally behind the brake pedal. Installing the vacuum pump was my biggest worry and challenge. Instructions are to zip tie it “somewhere”. That seemed pretty casual for a safety system. I chose, instead, to fabricate an aluminum bracket that attaches to the lip of the engine compartment and to the wheel well (this latter attachment point is necessary to keep the pump from vibrating). Finally, the kit comes with 3/8” fittings to tap into the brake booster vacuum lines. The Jeep, however, uses 8mm nylon tubing. Brake Buddy, via etrailer.com, stated that the tubing would stretch and all would be good. Again, this felt casual for a safety system. Instead, I purchased an 8mm check valve and a 8-6-8mm barbed tee through Another online retailer to do the job right. I had to heat the Jeep tubing to fit even the 8mm tee, so the is no way the larger 3/8” fittings would have worked. See photo of my finished vacuum line installation. Bottom line, it was a POA install, but looks great. Hopefully it will stop the Jeep when towing. I’ll find out soon. :D
# 6
Demco Air Force One Flat Tow Brake System for RVs w/ Air Brakes - Proportional
I wouldn't use anything else! Once this system is installed it's literally plug-and-play. Nothing to move or install into the car, each time you tow. Just plug it into the coach's air break system and you're done. Install video from etrailer made it even easier to complete. You do need a bit of mechanical guidance/assistance as you're connecting to both your vehicles and coaches breaking system but it has worked flawlessly for over 11,000 miles and in some pretty intense traffic.
AF1 is amazing so far. I did the installation by myself. I have a 2014 Honda CR-V and bought it for towing. Watching the video helped me through it. The car installation portion was pretty straight forward. The video is better than the instructions overall, but I read through the entire instructions before beginning. I was able to install the RV tank without putting the rig on a lift. Depending on how big you are and flexibility, it can be done with the RV on the ground...it just takes longer. Also, I would recommend knowing where you are going to mount your RV tank. I mounted the tank near the rear and didn’t have enough brake tube after doing the car. Picked up an extra 20 ft at Autozone or order the tube with etrailer. The customer service center is very helpful too. Many thanks to Mariah for the outstanding assistance. Finally, I would say that if you order the brackets to mount the emergency brake away for your car, you may have to cut them down with a grinder. It is so much nicer not putting the brake buddy in the car now. Looking forward to enjoying it on trips. I drove the rig about 20 miles yesterday, and the light came on and I honestly couldn’t tell the car was back there other than looking in the video and seeing the light on the car during braking. Highly recommend this unit.
# 7
Demco Stay-IN-Play Duo Braking System for RVs w/ Hydraulic Brakes - Wireless Monitor - Proportional
I installed this system in a 2023 2 door Wrangler. I also used an etrailer base plate and etrailer tow bar. I had originally purchased a Demco Delta Force Braking System. However, with the shape of the floor in the Jeep I was unable to use this unit. There are various places to install the stay n play duo in the Wrangler and the etrailer installation videos show this. I elected to install mine under the drivers seat as I wanted to keep it out of the elements. I fabricated a sheet metal bracket to mount it on that allows the rear seat heater duct to function unimpeded. Once installed the unit is out of sight and very simple to use. Just a flip of the toggle switch and its ready. I only needed to make a few adjustments to have it brake the way jeep the way I wanted. This is also a very simple procedure. I highly recommend this unit and appreciate all of the information etrailer has on their site to aid in the procurement and installation of their products.
eTrailer was very helpful in choosing the correct hitch for our rv and car. They also provided a special brake application in the car that makes it super easy for toad braking. I am 72, and I hook up this toad and pull it with confidence. The instructions to hook up the toad was presented with ease. They knew exactly what they were doing, and we didn't rush through the demonstration. I would recommend eTrailer to anyone.
What our customers are saying:
"very easy to shop"