Most Popular 7500 lbs WD GTW for 2016 Jeep Cherokee

Hitch was very well built. Great welds, and fit my Jeep Cherokee 1816 perfectly. Hitch was delivered very promptly (except for the one day delay of road closure)

Every part of this job was easy . From ordering on etrailer website, to doing the actual job with the help of etrailer help videos.

The hitch install was as simple as could be. My Cherokee had none of the options that would challenge the install like def reservoir, dual exhaust or spare tire. It took longer to set the torque wrench than it did to bolt it in place. Super simple, super easy. High quality and I like the look of the round tubes over the square one. Very happy!

I purchased a hitch for our 2013 Jeep Cherokee. I ordered on-line; and after receiving my confirmation - I noticed I made a mistake. I called customer service and they fixed the mistake immediately. The hitch arrived ahead of time; and I nstalled it in about 10 minutes. The wiring harness was a little more time consuming; but not difficult. Although; the ground wire was a little short; I had to splice in an additional length of wire. Overall; a very good experience - this is my second purchase; and would continue to buy from etrailer.com again.

The hitch fits perfectly snug in my 2014 WK2 Jeep (Grand Cherokee). I did lay down 3 solid coats of black paint and 2 coats of clear coat to help prevent factory chipping and thus rusting. I've been putting my Thule bike carrier in and out with minimal wear and tear on the contact points. Great investment and I would do it again.

Excellent purchase.!!!! The installation on my Jeep Cherokee Altitude 2017 took 30 minutes. It looks fantastic and it works perfectly fine.

I blindly ordered a Draw Tite receiver for my 2011 Acadia - based upon reputation. Had it installed and it cost me $100 do have it put on. Recently weather allowed me to proceed to installing my long term (CURT) 2 inch Ball bar with 2 inch ball into the Draw Tite receiver for work needing to be done and found that it would not allow inserting unless use of sledgehammer. I attempted to file down the misaligned (welded on) collar that was forcing the misalignment and was not able to make to make it work. Nichole at etrailer worked with me and replaced the Draw Tite receiver and I found the replacement was properly aligned and my Ball bar does now fit properly. So - presently had over double the cost for the defective unit and replacemetn that I should have. Being 82 year old I can no longer perform the task of handling this work.

Click to Enlarge

Click to Enlarge

Came 2 days early, didn't take my money till they ship it. Plus I never like to order anything online because I'm afraid it won't fit. But they said it would an it did( 2016 chevy traverse). Also it says 45 mins to install. Sounds About right 10 mins asking the wife an kids to help hold it up with no luck, 10 mins looking for my tools 18mm & 3/4 wrench,10 mins looking at the picture of the instructions because what GUY really reads it? lol, 10 mins putting it on by myself laying on my back in the driveway using my leg to hold it up & 5 mins putting on 1 bolt by the muffler because I didn't read the instructions an lower the muffler out of my way hahahah. P.s is you have soft hands I suggest wearing gloves an waiting for the muffler to cool off because i didn't ??. But all in all it was easy & fast to put on even if your by yourself. Definitely ordering again if I need anything for her car. Thanks etrailer

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I loved this trailer hitch. I installed it on my jeep gran Cherokee because I needed to tow my boat with it and the jeep didn’t come with a hitch. I would definitely recommend this company in the future!!

I did not have any plans to actually haul a trailer so I can't comment yet on how it works to haul a trailer, but I'm sure it will work as is designed... ... However, I purchased it because I became aware of the "Voluntary Recall" from Chrysler because some of the 2003 Jeep grand Cherokees had safety issues because of the potential, that; under certain conditions, when in a rear end collision, in regards to the gas tank, there is a potential for the gas tank getting ruptured and a potentially deadly fire occurring, so I wanted to double-up on preventing that. I decided it was a necessary preventative measure to get this 'Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" '. As far as the quality of the actual product, I would give it a 5 star rating, but instead, I gave it a 4 star rating, because of the inadequate packaging it gets shipped in. I ended up having to get a total of 4 shipped to me for 2 different purchases of this product because of; 1- the 1st one was bent, not so bent that it was obvious, but it just wouldn't bolt-up to the Jeep. I don't know on the 1st one, whether or not it was bent because of a manufacturing issue or from shipping damage. It didn't look bent to the naked eye, but it was. I measured between the mounting holes and discovered it was almost 2 cm off from being equal at opposing diagonal cross-section measurements. The one that it was replaced with, (the 2nd one), bolted right up with no problems and the diagonal cross-section measurements were much closer to being equal. 2- After the Jeep got rear-ended, I wanted to get another new one to install after the body shop repairs get finished for the same safety reasons mentioned above. On this 2nd one, which turned into a 3rd then a 4th one because of shipping damage, as with the 1st one, the shipping damage to the packaging was somewhat severe. The hitch was loose inside of the box and flopping around and part of the hitch was protruding outside of the box... ... Because of that, I was concerned that the Receiver Hitch was probably bent out of proper mounting alignment like the 1st one was. Also, I was not able to get engineering specifications from etrailer.com for the exact measurements between the mounting holes in the Receiver Hitch so I wasn't able to take any measurements to compare. So, just like the 1st one, (the 1st purchase), I returned it for a what would hopefully be an undamaged and not out of alignment or bent replacement, which I did receive. The body shop won't be finished with it for another couple of weeks so I won't know if it bolts up or not, but I'm pretty sure it, like the 2nd one that I got from the 1st purchase order, will bolt-up as it's supposed to. That being said, I am very glad I did get the Trailer Hitch Receiver the 1st time because I was hit from behind by a low vehicle and I think it prevented a rear end collision caused Gasoline Fire and potential serious injury, or worse from happening. Also, the Trailer Hitch Receiver will work quite well for hauling any trailer that the Jeep is legally able to haul and it will work well with a Hitch Mounted Wench or with a Receiver Tow Shackle for when I do go on Four-Wheel-Drive Adventures.