Most Popular 9000 Lbs Line Pull for 2016 Ford Expedition

Awesome experience!

The hitch seems to be excellent. I have not yet been able to install it because the bolts, etc supplied with the hitch are useless because there is no way to insert them through the frame rails due to the slot id too small to accept the bolts. I am tempted to use the factory bolts, but I am fearful of allowing the factory nut assembly to slide away from the holes making them inaccessible. I think the better application would be to supply and use stud bolts which would allow installation without risk of inaccessible nuts inside the frame rails. This is what I intend to do when I can purchase the studs

It's was extremely easy to install I did it myself in about 15 minutes . And it looks great

I think this hitch is top notch and the instalation kit made the install really easy like

Like the product. Got it very quick. Installed and love it.

The Curt Front Mount Trailer Hitch Receiver worked perfectly on our 2021 Ford Expedition to carry our bicycles while towing our travel trailer.

Fits 2018 Expedition perfectly. Fish wiring the bolts through the frame was a cinch.

Super easy to install product thanks to the video! Took all of 25 mins to install

Great product,easy installation and dealing with etrailer has been a real good experience.

I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.

Hi George, I received your email and didn't realize it had been a year already. I'm afraid I don't have anything to say that you want to hear but I will tell you anyway. I spent about a week researching this hitch and read numerous reviews about it and how easy it is to install with installation times of 30 minutes to an hour, so finally I bought one. I read the instructions when I got it, looked simple enough. I've been building cars and motorcycles most of my life, a few hot rods and drag raced Harley's for 8 years, and I had to fabricate a lot of parts on the drag bike splus I've been a CNC Machinist for 30 years, and having just retired this project was on my list of things to do NOW! Well its been a year and the hitch is now sitting in the corner of my dining room. Either I have a Jeep Cherokee that is an odd ball or its just my crappy luck. In the directions it says to use the fishwire for putting in cm-sp1 and the bolt. I can supply pictures if you want but there is no access hole anywhere near big enough to get the sp1 spacer in the frame and the end of the frame isn't open either as the directions suggest. Apparently its either butcher the frame with a hole big enough to these spacers in, which I really don't want to do, or try to sell the hitch for whatever I can get and say the hell with it, except I really need that front hitch. I realize most people are very happy with your product, but I'm sorry to say I'm not at all. You asked!

Installation was a breeze. It also is tucked out of the way.

This hitch was very easy to install....I had to trim the lower air dam to fit around the receiver and that gives it a clean neat look. I didn't like that I had to remove and leave the shields around the tow hooks off. But overall I'm very pleased. I plan to use this hitch for maneuvering a camper in a narrow spot beside my home, and for a bike rack when towing a camper.

Excellent from researching, ordering, fast shipment! Years ago I purchased a front hitch for my 2008 F-350 from etrailer. It was a no brainer to buy for my 2024 F-250. The videos make installation a breeze. Thank You

I put this on my 2022 F450 so I can carry a bike rack while carrying my slide in camper. Overall fit was great and the video on this site was very helpful. I did have to slot the brackets on the auxiliary cooler about 1/4" with a file so it could sit up higher so the hitch wouldn't put a lot of pressure on it. After that it all fit together nicely.

Finally got it installed with the help of a seven year old (because her hands were small) holding a fastener at a difficult-to-access location. The front hitch works fine. Used a floor jack to hold it in place during installation. Instructions not particularly clear or accurate in my case. I should have been told that the front air foil needs to be removed completely (and discarded). With the labor provided by two adults & a little girl, it took the better half of a day to install it. It ends up being pretty low - I had to mill and grind the bottom of my hitch ball adapter so it wouldn't catch on anything when backing up. You need at least a 6" high hitch ball adapter.

This is the second front trailer hitch that I have purchased from etrailer and once again the service and delivery were excellent. If your not mechanically inclined the instructions leave a little to be desired. Installation on my 2013 Ford F-150 was straight forward and took me about 3hrs. The unit is heavy duty and solidly made, so you will need some type of lifting device to hold it in place while you bolt it into place. You ma y also have to cut out two additional notches in the facia to enable sliding the receiver forward enough to line up the bolt holes. I use this front hitch for moving airplanes and it does a great job.

I use Curt Front Hitches from ETrailer with pintle hitch plates to make my own front protective bars and also rear protective bars in a rear truck, SUV. Or van hitch to protect my vehicles from bad drivers. Much stronger than bull bar or offroad front bumper bar protection

We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Great solid piece, as you would expect. Extra longer bolts are included in case you have the factory tow hooks, a nice touch and saves $10 at the hardware store. Not a complaint, just info; you have to remove the bumper to fit the front bolts, they won't drop in past the bumper brackets at least on my '95. Cut a hole and some minor trimming, and it works with the factory air dam as well.

Requires permanent removal of the front air dam. Requires temporary removal of the front sway bar. May decrease offroad performance by lowering the approach angle. Has 2 Sturdy retrieval loops.

I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer

The front hitch solved a storage problem that I was having with my truck camper.It fit perfectly. I added a Stow Away hitch frame and a UWS small aluminum storage box for my small generator. The photo shows a test fit before installation.

This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

2nd hitch, both fit up great. Left off the roll pan and built our own cover for the sway bar disconnect.

This front receiver mount is exactly what I needed. Great build quality and easy to install. Thanks for getting it to me in a timely manner.

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

UPS was rough on the box but everything still lined up without having to pry but was snug on the back bolts. Install was very straight forward and did it myself in my driveway in just about 90 minutes from pulling the air dam to putting tools away. Used my floor jack to support the hitch in the center and started with the front bolts on both sides and then pivoted the hitch into position for the back bolts and then snugged up all four mounting bolts to the 110-ftlbs torque spec. Hints. made sure that front of the hitch was just a a hair pointed up from level before tightening down all of the mounting bolts. I pulled the air dam completely off and then lined it back up in position lying on the hitch so I could marked it, so I knew exactly where I would need to trim it and then used my Dremel tool with a cutoff wheel to trim it to fit. Then bolted it back into position and was done. I'll try and update this post once I take some pictures other than the shipping box

Please read: I am not happy with this product. I have a 2023 F-150 with a 2” leveling kit up front. My properly installed hitch only has 8-3/4” of ground clearance sitting on my flat garage floor. It definitely appears to be the lowest point throughout the whole bottom of my truck.I didn’t even have to cut my air dam for the unit to align with the mounting holes in the frame. Like anyone else I wanted this to sit as high as possible, forcing me to cut as much air dam as possible. I believe the mounting holes in this hitch were drilled way too high, and now I’m either stuck with terrible clearance or I need to take it off and re-drill the holes lower on my own. Plus it points downward out the front and not on the same parallel plane as my truck. I put an accessory in it and it was barely above the ground out front. Super irritating. See photos. If anyone has help I’m certainly listening. The shipping and ordering was super fast and easy otherwise this would be 1 star.

UPS was 8 days late for no good reason though it looks like they used the hitch as a crash test dummy. It’s a miracle the hardware bag made it but it did! I think this is superior than the other brands available. They always include these little threaded fish tape wires for getting the hardware into the frame. I’ve done a transit and now this. Saves a ton of time/headache. However the instructions just have a diagram. Took me about 20 min to get the first bolt in. Then 20 min for the rest of the install. So if you read this, you can probably get the whole thing done in 30 or so which is what i expected initially. Tools: 3/4” socket Torque wrench 1/2” drill bit & drill OPTIONAL: floor jack to lift hitch into place. Steps: - Drill forward holes to 1/2” and shoot with some rustoleum or equivalent paint. Let dry for 20 min while you eat lunch, take a dump, whatever. - send fish tape through forward mount hole and out front of frame rail. Figuring this is what slowed me down on the first one. the carriage bolt head won’t fit through any of the obvious openings. See pic. - put to bolt plate onto the fish wire then thread the bolt onto the wire. Pull em all through the hole and watch it assemble right before your eyes! - repeat on the other 3 bolts - jack hitch into place and finger tighten the washers/nuts on - torque down to 75ftlbs and boom! time to yank or be yanked! See all my pics and if this helps, send me an imaginary beer through the quantum field! Econolines rule!

I tried ordering this exact hitch off Amazon. Not once, but twice they shipped the wrong part number. Took a couple months to get my money back. Etrailer got it right the first time. I took about an hour to install on my 2006 class B+ E 450 motor home. The best advice I can give is take the 15 minutes to remove the front bumper (21 mm). With front bumper removed you won't need the wire chaser things. Jus stick your hand in the frame.

A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.

Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.

Worked out great.. A little trimming on the facial of the bumper.. The fish line awesome little tool... Thanks

I have a 2005 Ford Explorer and this hitch fit well. There are three holes on each side of the hitch. The front two matched perfectly to holes existing on the frame of the Explorer. I had to drill into the frame for the third hitch hole but it was not too difficult. The hitch comes with a fishing tool to get the bolts where they need to go in the frame but it works pretty slick. Much easier than some fishing I've had to do with electrical work. I am not a mechanic but do handyman jobs around the house and was able to install this hitch by myself in 1.5 hrs. After placing the two front bolts, I propped the hitch up on boarts to where the bolts came through the hitch holes then screwd on the nuts to bring the hitch up & into place. For the third bolt, I drilled with hitch in place then put the bolts in the third hole.

The fit was a bit too tight but we were able to make it fit. The shipping packing was pretty lacking. Since being installed we have been using it with a spare tire mount. That works great and it makes the spare tire more accessible compared to the standard under the bed mounting. When fully loaded with a camper and towing a boat moving the spare tire to the front improves the weight distribution.

Curt actually recommended that we use etrailer. They even gave me the confirmation that the hitch would work and told us you have a video. Thanks!