Most Popular Draw-Tite for 2013 Hyundai Santa Fe

2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.

My order arrived in two days. I am impressed both by the layout and functionality of etrailer website and by the quick, free shipment. The hitch for my 20007 Hyundai Santa Fe is well made, well finished and fit perfectly. The estimated installation time of 30 minutes would probably have been accurate had I not had to clean 3 years worth of rust from the mounting nuts installed by the factory. Once clean (no simple task since reaching them with a 10m/1.25 tap was difficult) mounting the tow bar was simple and made easier with a pair of jackstands. Owing to the design and location of the mounts, reaching them required the use of different ratchet extensions and flexible joints and I'm not certain of the accuracy of any torque reading. In summary, I am pleased with the product and impressed by the follow-up from etrailer. I will recommend them without hesitation.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

We used our car hitch and cargo carrier last summer in a Honda Accord to support a cargo carrier. It held up great on a 4,000 mile camping/hiking trip from Mid Missouri to Glacier National Park, MT. We were able to use the carrier/hitch to carry our large tents and baggage (approx 120#)directly behind our car trunk. Initially I was a little hesitant at the smaller 1-1/4" tube hitch, but it was very stable throughout the long trip. Sure was a lot less drag than putting all our gear on a roof cargo carrier.

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

The ball mount is just what I needed but I think the packaging could have been stronger. One end was ripped open.

Basically I bought this ball-mount after I installed the low-slung hitch receiver from ETRAILER to know I have an ability to haul something if really needed in an emergency situation. The receiver hitch was purchased for my Thule bicycle rack , purchased from Etrailer.

The shipping was quick. I've also owned it for a year and the product is solid. Besides the sticker wearing, the hitch is perfect.

Excellent service. Fast delivery. Very Satisfied.

arrived in excellent condition. Customer service from E-Trailer keep me informed on the delivery status of the hitch drop

Just as advertised and solves my problem of trailer tongue level to hitch position. Delivered on schedule with no hiccups. Fits perfectly in the 2" factory receiver on my Jeep JKU. The 2" ball in the picture is a reused one not new which is why it has rust on it.