# 1
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
My Iowa 2009 Camry has been in a garage it's whole life, so, that helped a lot. Used [online] etrailer video for ease of work. I took longer than they did as I had to work a bit to de-rust a couple of female bolt threads enough to get a bolt on easily.
We bought this 1.25" reciver hitch last year to accommodate a Kuat bike rack. The install was easy, the mounting holes lined up perfectly on our Camry, and the black painted hitch finish still looks new. We are very happy with this purchase.
# 2
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
I didn't cut off any underbody panel pieces. I just made a slit for the hitch to slide through. Also didn't cut off any heat shield. I drilled a hole for the 1/2" screw and torqued it to xx ftlb as instructed. Every thing worked fine. Hard to believe the video instructed to cut off that much. A bit crazy IMO. Also.. super snug fit. So snug I had trouble getting the M12 bolts to line up with the thread in the subframe. Pain the ass, but eventually got it in.
Fast delivery and everything fit perfect. Easy installation after watching etrailers videos. Lowest price I found on the internet for this hitch. Thanks for the great service.
# 3
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
Finally got the chance to install this hitch. The written instructions are marginal. They did not cover my hybrid version. The installation videos on etrailer were more helpful. The hitch was a bit off and contacts the tire well on one side. Installation by loosening the exhaust did not work for me. Mine was too tight and I could not move it out of the way to drill. I had to remove the muffler. The instructions for trimming are a bit aggressive. I was able to get the under cover installed with about 25% of the suggested cutting. One thing the instructions left out is a rear edge trim (however, the video did mention this). I also added a strip from (the heat shield scrap) to tie the cover back together and prevent flutter noise while driving. Installed, this hitch appears sturdy. I am sure it will last. Too bad it did not come with a pin or cover.
This is a quality product. It’s designed to fit the car perfectly. Please not though that you’ll need special tools to disconnect/drop the muffler system to install the hitch. I did not have tools to disconnect the muffler/exhaust hangers, so I wound up taking it to a mechanic that installed it for about $100.
# 4
Curt Trailer Hitch Receiver with Standard Drawbar - Custom Fit - Class II - 1-1/4"
outstanding easy and just what I needed great product and price plus the wiring I ordered went in easy as pie
A difficult installation. But, that was not because of the hitch. Once the car was apart, the hitch fit perfectly and bolted right up.
# 5
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
This also worked
Very easy install and works perfectly
# 6
Curt Trailer Hitch Receiver with Standard Drawbar - Custom Fit - Class II - 1-1/4"
These are some of the best trailer hitches I know for the Toyota camry. Easy to install. I did order the wrong ball, had to buy another, to large of a bolt size.
Quality product. Worth every penny!
# 7
Curt Trailer Hitch Receiver w/ Euro Drawbar - 1-7/8" Ball - Custom Fit - Class II - 1-1/4"
# 8
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
I installed this trailer hitch on my 2018 Toyota Sienna. It is very well-built, and fit perfectly. Customer service was very responsive when I had some questions, and responded right away, both by phone and email. The instructions were very good, but could benefit from additional information regarding cutting the car’s rear trim panel. In addition to the cut that needs to be made for the trailer hitch bolting plate to go through on the driver’s side , it also needs to be cut around the main bar / receiver area. Instead of cutting a big slot for the main bar, I cut out around the receiver plates, and put drain holes in the ends that would otherwise collect water. One shortcut that I found was that I was able to move the exhaust out of the way far enough by just removing the rearmost hanger, rather than removing the two hangers as shown in the video.
2012 Sienna LE FWD. Watch the 2011 installation video before you start. This 13105 hitch tucks in even prettier than I expected, and now my brother is jealous. Note I made the cutout in the underbody panel narrower, starting 1.75 inches from the hole (see photo), for a closer fit, and there is still room for torque wrench. I also cut a slit out to the front edge, so I could slip it on with the hitch in place, and for better access to my air hoses inside the left fender. I decided to add Airlift after reading reviews, since on trips I carry a maximum load. Installed single-handed, raised on jack stands.
# 9
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
For an open box item, youd think it was brand new! Came with all the hardware and I installed it in about 10-15 minutes. Torque specs were included with directions as well. A great purchase, Im very happy. Thank you!
I was disappointed that the hitch came slightly bent. I had to use a bottle jack to widen the bolt holes by 1/2-3/4'' in order to bolt the hitch to my car. otherwise it works fine for my 2005 Toyota highlander.
What our customers are saying:
"hitch arrived on time, and it took me about 10 min to put it on . thanks alex"