# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It was a bit harder to put on than they show in the video. Did it by myself, everything fit perfect SO OWSOME! I would recommend anybody. Truck or car should add one. Very convenient and can be use for many different purposes.the rack on the back, I now put in the front with generator gas tools and it works as steps. So now I can tow trailer, or jet ski. Having that front hitch is so cool. You could even attach a car whinch in the receiver.
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This item showed up extremely poorly packaged with two holes in the box and paint missing where my hitch came out of the box and was beat up while being shipped.
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!
VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )
# 7
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
The hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I am not sure that installing this hitch could have been easier. I did it on the ground on my driveway, sloped, by removing my tow hooks and supporting the receiver on some blocks and bolting it in place directly into the frame. The hardware fit perfectly in alignment and thread size etc. We've mostly used it to carry bicycles when towing, though once placed a trailer with it also. Strong, fully functional and as noted easy to install.
Haven’t had a chance to use the front hitch on our Nissan Frontier year but the installation was quick and easy. I was all set to knock the installation out in 20 minutes until one of the split lock washers failed and had to be replaced out of my spare stock. Also an additional note: the hitch showed up heavily scratched despite the packaging having been in good condition. Maybe some more careful handling at the warehouse is in order.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I ordered this unit after sending one back from a different supplier ,the previous one said it fit my Ranger, well after getting it and checking installation video`s it needed to be cut up and fafbricated, no thanks. The Draw tight from E-trailer fit great,delivery was prompt even with a major snowstorm ,the only hic-cup was I didn`t take off my front bumper,due to a brush guard we welded on years ago but even without taking off the bumper I was able to get it on , heck I didn`t even jack up the truck. A little trim on the bumper trim and some help from my motorcycle jack easy to do , took about an hour and a half looks good , fit great, now its time to attach the snow plow and get my driveway clear.I am also ordering the air bag spring helpers for my little truck and will see how that goes too, thanks to the staff at E-trailer, I`ll be ordering from you again.
This is a great addition to my old square body Explorer Sport, the closest thing I can afford to a square body Bronco. Great for moving trailers around the yard or put a hitch mounted bike rack up front and tow your boat or camper behind. Best part was no drilling direct fit and in stock at etrailer!
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."