Most Popular Below the Bed for 2001 Dodge Ram Pickup

Excellent product, great service, I highly recommended etrailer .

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installation was fairly easy on my 2001 Ram 2500. My brother and I got it installed in about 2.5 hours. Simple and solid design. Hooked up 38' car hauler and off we went. Only problem we had was the measurement Curt provides for the 4" hole location in bed floor was about 3/16" too far toward the cab, hitch lines up with hole but on my truck it is not centered (bed floor brace prevented us from being able to move hitch further forward). Not a big deal!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The best price on the market, and the fastest shipping I have ever seen. It was easy to install and worked great!

I ordered the Curt ball,and safety chain kit for my new 2018 Ram 2500 with factory hitch. A excellent value,for a quality product, that saved me a lot of money compared to OEM dealer price. Fast shipping had me ready to tow, in no time at all.

Click to Enlarge

Click to Enlarge

I bought this product to us in my 2016 Ram 2500 with the 5th wheel prep and an Andersen Ultimate hitch. It is top notch quality, and the anchors DO work with my Ultimate hitch. The fit is tight, but the anchor mounts do clear the hitch base. This is a well made product in a nice storage case. I recommend it.

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Seems to be very well built. Shipping was very fast. Will definitely purchase other products.

The hitch works fine and was easy to install. Everything fit well with one exception. The rod that locks the ball in place from the wheel well is too short. I expect it is the wrong rod for the 2013 Ram pickup. I made an attempt to contact etrailer to get another, but failed to contact anyone. Can you put me in contact with someone who can assist me in getting a replacement?

Installation was fairly easy on my 2001 Ram 2500. My brother and I got it installed in about 2.5 hours. Simple and solid design. Hooked up 38' car hauler and off we went. Only problem we had was the measurement Curt provides for the 4" hole location in bed floor was about 3/16" too far toward the cab, hitch lines up with hole but on my truck it is not centered (bed floor brace prevented us from being able to move hitch further forward). Not a big deal!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The best price on the market, and the fastest shipping I have ever seen. It was easy to install and worked great!

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Very nice hitch, took me about 3 hrs to install on a 2014 RAM 2500 6.5 bed with help from the wife. The hitch is very thick steel, probably close to 1/2". The ball works great, very easy to secure and remove. Very happy with the hitch and glad I chose it over the turnover ball which seems to be slightly harder to install. Some tips... remove spare tire, remove heat shield, drill the 3 1/4" hole, make sure to use a good hole saw made for metal, positition the nuts using the brackets, have someone get the bolts started while you hold the hitch. Tighten the bolts, you will probably have to remove the exhaust hangers to move the exhaust enough to tighten the passenger side bolts, torque to spec, drill the safety hook holes, install safety hooks and put everything back together...thats pretty much it. I took my truck and had the bed Linex'd after I installed the hitch. They touched up around the holes. Looks awesome!

Click to Enlarge

Ordered the Curt underbed gooseneck trailer hitch for my Ram 2500 from etrailer.com. The pricing was great and hitch was delivered quickly. Installation is easy with assistance from one other person. This is a quality hitch and will serve my needs.

Installation was fairly easy on my 2001 Ram 2500. My brother and I got it installed in about 2.5 hours. Simple and solid design. Hooked up 38' car hauler and off we went. Only problem we had was the measurement Curt provides for the 4" hole location in bed floor was about 3/16" too far toward the cab, hitch lines up with hole but on my truck it is not centered (bed floor brace prevented us from being able to move hitch further forward). Not a big deal!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The best price on the market, and the fastest shipping I have ever seen. It was easy to install and worked great!

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Easy installation. Works great with our 36ft triple 7k toy hauler.

Click to Enlarge

This hitch is a good example of great engineering. The parts were complete and very good quality. A few "pointers" to help with a "first timer" with the process would have been to have some stickers attached to the pieces that provide some orientation, e.g., "Towards Cab", "up/down". It would have saved a trip to the store if I had easier to find hole diameter information... maybe on the ordering page... "3-1/2" hole saw required". The video was helpful and appreciated.

Get a turnover ball and don’t be the sucker I ended up. I laugh every time I think of the convenience I thought I was getting by not having to climb in the back of the truck. I don’t know if mine is defective or if this device is actually a workout program mixed with an anger management exercise in disguise. I’ve been using it for a year now, but within a month I developed a strategy for getting my trailer hooked up. First I climb into the back of the truck to cut the duct tape off I’ve used to attach the worthless rubber cap which falls off every chance it gets, filling the mechanism with whatever you have in your truck. If you ever plan to do anything with the bed of the truck besides pulling your gooseneck, haul hay, a four wheeler, anything dirty it will definitely jam your ball. After the tape is off I fight the first lever, I yank, turn, pull, twist, bang, swivel, dance this lever into the exact position. I climb under the truck and cover myself with wheel grease and scum getting the thing to unlock. Then the second lever, to lift and drop the ball. Repeat the steps of the first lever with less twisting, but add climbing into the bed with a hammer, banging the ball, climbing underneath, banging the lift arm, banging underneath, shaking, bouncing and sweet talking this POS into the upward position. Stop to spit curse and wipe the sweat out of your eyes and clean any wounds you got banging your knuckles. Now repeat the first lever steps AGAIN, including going under, going up, and under and in the wheel well so far you find whatever you ran over the other day that made you say “hmm” all over the front of your shirt. Repeat in opposite order when you want to put it down. I’m so embarrassed about this hunk of junk that I stop on the side of the road a half hour before I get to anything I’ve got to pick up just so no one has to see me cursing, crying and throwing a tantrum getting this thing in place. Please don’t buy this item, you don’t deserve this kind of punishment.

Nice solid unit that will definitely last a lifetime but even new this unit is not very user friendly. I have it installed on a 99 c/k3500. Installation of the unit was easy but the 2 levers for raising and locking the ball are not well designed. if you pull the left handle to far, the ball gets stuck in the down position and you have to crawl under the truck and push it back up. The right handle is supposed to somehow lock it into position but I have yet to figure out a reliable system for doing that. I had to shorten both handles to clear the rear tire and with the tire blocking the handles it is difficult and dirty to operate them and usually you smash your hands when the levers do finally go into place. The rubber cap is worthless and generally ends up bouncing out. On my 2nd truck, I went with the style you put the ball in by hand and it is a much easier unit to operate.

I recently purchased a 2016 Ram 3500 with 5th wheel tow package already present on truck. I wanted an additional goose neck product and looked at various suppliers online and found etrailer products offered for sale. After to speaking with Heather who answered all my questions as well as reviewed feedback from customers I chose to go with the Reese gooseneck kit. I received the product within the shipping date provided to me and I went out to install it. It took me all of 3 mins to install with no issues. I did my best to remove, shake and couldn't get them to budge. It took me a total of 5 mins to remove the parts and storing them back under the rear seat. The parts fit perfect, look great as well as we're the cheapest price I could find. Their online video is all the install instructions you need! I will definitely use etrailer in the future. Thanks Heather!

Click to Enlarge

Click to Enlarge

Product took less than a minute to install on my 2015 Ram 3500. Would highly recommend this product for those who have the factory 5th wheel and gooseneck prep package from Ram in their truck.

Click to Enlarge

Installed hitch looks it came that way from the factory. Difficulty level 4 out of 5 for a DIY'er working alone. The front-to-back measurement in the bed is critical for drilling the 4" hole. The measured distance given in the instructions leaves little room for error in the forward direction. Better to measure a little short, than a little long! As advertised, there was no drilling required in the frame rails, but I did have to remove the frame alignment tabs on both sides of the bed; Sawzall or cutoff wheel required. In the end; it was a full day's project, but well worth the effort!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This B&W gooseneck installed easily on my 2001 Dodge Ram 2500 in a little under 4 hours by myself. The only drilling required is for the holes in the bed for the receiver and the safety chain hooks. I'd definitely recommend a tip I saw online-- use a 3/4" piece of plywood as a template/stabilizer when you cut the 4" hole in the bed because the hole-saw will want to bite and grab badly on the bed without it. Quality product made in the USA by B&W, this is my 3rd B&W hitch and they will last forever. I will use this and another in my wife's truck so we can have one fifth wheel hitch (Companion) that will fit both trucks. Great service as always from etrailer. HIGHLY recommended. Thanks!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge