# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Overall, my experience with etrailer was good. There was an initial delay in shipping, but once I talked to someone, everything went well. The help page was invaluable. The biggest help was the installation video. While there are slight differences between the 2011 GMC and the 2013, the process was the same. I am very pleased with the product and the support. Picture attached.
Great product! Super easy to install! This makes my winch twice as versatile. Thanks for a design that leaves the tow hooks in the truck!
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The questions that you answer about what truck you have do not get all the way to the correct model. So then when you scroll through the available products, it is showing products for different models that dont apply to your truck(like the 1500, 2500, 3500 etc). However, you dont realize this as you just finished putting in the inputs for your vehicles and then of course assume that the list they give you of available products would only include your vehicle since they say "confirmed fit" for your model. They sent me the hitch for the gmc sierra 1500, which does not fit my 2500 GMC and then want me to pay the $50 to send it back. It seems like the designers of the website should have finished the job before they went to lunch. Now I am out the money.
I ordered both the front and rear Curt class 3 hitches for my 2008 Gm sierra. The factory rear hitch had rusted from the inside and had split all the way across. This new hitch is a lot more heavy duty , with thicker metal and the ends are sealed to keep water out. I liked it so much , I ordered this front hitch to use our bicycle rack on front when we pull our camper . Did not know how to carry our bikes until I ran across this hitch on Trailer. I think it will solve our problem . Thanks etrailer !!! Also had best price, got free shipping, prompt service, and excellent customer service !! Will definitely order from them again !!!
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This is the second hitch I've ordered for my truck. This hitch was very easy to install on the front of my GMC Sierra and is almost unnoticeable, which I like. I use it to transport a small Honda Trail 90 motorcycle, and it's 9000lb rating is well above what I am asking it to do. It arrived via UPS several days after ordering, was in good shape, and only took ten minutes to install with only two different size socket wrenches. Highly recommend this unit for the front of any truck.
Repetitively easy to Mount and was still able to keep the factory toe hooks installed
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Perfect fit, quick and easy installation. Only took 25 minutes by myself. I would highly recommend this hitch. Plan using it for bike hitch, winch, cargo platform, etc.
Arrived as scheduled. Front hitch for 00 GMC Sierra as ordered. Application 1.5 hrs to install. Satisfied with purchasing experience with etrailer sales dept.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This Curt 31109 front hitch went on a 2009 GMC 2500 Sierra crew cab with a Duramax Diesel. Shipping was incredibly fast - just 1 day! The hitch appears well built and nicely finished - and it's made right here in the USA! It fit perfectly and was very easy to install. No trimming of bumper plastic was required. My wife and I are retired and we use this truck to pull a large 5th wheel trailer or carry a truck camper. We will transporting our bicycles on the front hitch. I should have done this earlier.
Great quality, installation is very easy, cost is good. Definitely happy with this product and the service.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product is great! Exceeds my expectations for ease of installation and performance. I removed the 3” spoiler completely vs cutting for hitch. The key is to “dry fit” in place and use a metal punch to mark all your drill holes. Wire bolt feeder worked great for installing bolts. I used the hitch to mount my eight pole rod & cooler holder for surf fishing.
Super fast shipping,but could use better packing.Hitch actually made a large hole in box,UPS driver had me check to see if anything was missing.Easy install,but try finding a 17/32" bit. After seeing how big the front opening is I just used a 1/2" bit. I think it took longer to remove, trim and reinstall the front spoiler than the rest of the job. Looks great installed
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The Curt hitch assembly arrived in excellent condition. As usual, George did a fantastic job of getting my order to me very promptly. The installation went perfectly and exactly as shown in the video on the etrailer.com website. The front hitch fit was perfect on my 2015 GMC Sierra.
This product is super easy install (took me less than 20 minutes all by myself). No cutting or drilling required. The product also works great. This makes backing a trailer into a tight spot much easier. The only down fall of this product is that it has to drop down pretty close to the ground to clear the lower air dam on the Sierra 2500HD. The remaining ground clearance leaves the hitch low enough to hit the ground when pulling up to tall curbs or parking blocks and would also likely hit ground fairly easily while four wheeling. The low ground clearance is the only reason I gave this four stars instead of five stars. Please note that to get a front hitch that is no cutting or drilling, there is no other option...it has to be below the air dam.
# 9
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
# 10
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
Product shipped and received on time. I'm very happy with the packaging. Hardware was included with instructions to install the hitches I purchased.
# 11
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very easy to install. works great for bike rack and generator box.
After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .
# 12
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Very easy install on 2017 sierra 1500. Took an hour by myself without jacking up truck. With two people and a jack could easily be done in no time. Jack is not needed but would’ve allowed a little more clearance to drill holes easier. Did not have to trim any of the fascia
Great VIDEOS and helpful questions and answers service. Fit my 2014 Silverado present and I had a good idea how the job would go before the hitch even showed up.A little slow on the shipping but other than that very happy with my purchase.
# 13
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great customer service and product.
The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.
# 14
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great product,easy installation and dealing with etrailer has been a real good experience.
# 15
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Installed on my 2019 GMC Sierra 1500 Denali. Shipping box was destroyed & poorly packed. Instructions were straightforward. Install took 1 1/2 hrs. I only trimmed the thin trim without cutting the skid plate. The receiver pushes up on the skid plate slightly, but I didn’t want to cut it. Should work great for my E-bikes when pulling the RV.
Muche easier and quicker install on my 2020 GMC Sierra Doublecab. As a note, i didn't cut the front airdam. I removed the bottom piece (which had been chewed up a little bit by higher curbs and then was able to just slightly push up the air dam. My wife thought you couldn't even notice and certainly easier than cutting (because you can never put it back LOL). Overall a quick install that went very easy. Very satisfied.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!
Primarily bought the front receiver hitch to haul our 2 e-bikes. Did that because it was easier than hauling them inside our camper. And didn’t trust them bouncing around on the back bumper of the camper. Hauled the bikes that way on several camping trips. Easy as pie and I could keep an eye on them the whole trip.
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
A good install! A bit of trimming for my application , but the bolt holes lined up perfectly. This front hitch was not specifically for a Lexus GX 460 but I decided to try it. There is a small area of lower bumper plastic that had to be trimmed. The hitch was pushing up against it before it was high enough to be in place. Upon trimming that area, it went in perfectly. If trimming the lower plastic is not for you, probably best to pass. However for my use, it works well. It is a stout piece, very strong. I added a pic with a red line to show where the trim needs to be.
Installed on my 2012 Lexus GX460. Perfect fit once I cut the center section of the lower plastic area for it to fit. Also had to trim the bottom splash guard and bend in the L brackets that hold it on. Took me about 2 hours. Very happy with the outcome. Now can mount snow blade for the driveway clearing…or any other hitch items.
# 18
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this after years of struggling to get a race trailer in the backyard. When I decided to move it about 12 feet to the right, I knew there was no way my F350 4X4 crew-cab could make the tight turns that would be required. After being able to position it on the first try, I realized I should have bought it 20 years ago. The installation took two tries. Not sure if it because I’m 66 or trying to do it by myself. The key for me was to hook a couple of straps to it, unbolt it, and then put the bumper on the engine compartment. The first attempt was by trying to do everything from the backside. Once I removed the bumper completely, I was able to do everything from the from, so I was not completely blind in installing the two side bolts. The straps not only made it easier to reinstall it, they were useful in pulling up on side to level it. I will be buying my son one for his 2016 F150 4X4
Package shipped and arrived quickly. Install was relatively easy, but took longer as the bolts were actually larger (7/8") - and I did not have a shallow socket for it that was also 1/2" drive for my torque wrench. I also needed remove the grill cover to have enough throw to tighten back on the bumper after the hitch was bolted on (which blocked access from the bottom). I would recommend getting some 9/16" shank carriage bolts to help align and secure the front flange while tightening the sides to the frame. I used a floor jack on level pavement to raise the hitch into position. Overall - it looks great and functions well. Very stout and strongly built with superb welds and finish. This will make getting smaller trailers into tight spaces MUCH more easier and less of a headache/embarrassment. Plus it's also another point for recovery as an option for 4x4 or overlanding, and I also added a step to the front of it which makes accessing the back of the engine bay easier.
# 19
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Picked this up from etrailer for a great price, so i can put a hitch-mounted winch on the front of our race tow vehicle (and perhaps use it to get the trailer into tight spots). As always with etrailer, it was delivered quick (and free!). One of the arms was just slightly bent (perhaps from shipment) so I had to whack it a couple times with a heavy hammer to get the holes to line up, but after that it fit perfectly. The little "fishing" tool included is extremely handy for installing the two bolts that need to come from inside the frame of the truck. All in all, quality is great and this particular one fits with my factory skidplate/splashguard with a small amount of trimming with some metal shears. PS - we also have stuff from etrailer on the rear end. Highly recommend anything you buy from etrailer!
My hitch arrived quickly and my mechanic installed it in 1.5 hours for me a few days later. The factory skid plate fits nicely with 2 holes cut as a modification. His only concern is he will now have to use hand tools instead of his air tools on some bolts holding the skid plate at oil change time. But no big deal at all. I keep a 16 foot boat in my warehouse and maneuvering room is very tight. The door is narrow and there is a building across from my door that leaves very little room to maneuver my truck in. With my new front hitch I put the boat in the warehouse in less than a minute the first try. The front hitch makes it easier in 2 ways: 1) visibility-you can see what you are doing. You are closer to your work and you are looking straight at it. 2) with the trailer closer to the front wheels you can do things in tight quarters that just can't happen working with the rear hitch. Using the rear hitch the front of your truck would hit the wall of the opposite building. My only regret is not getting this ten years ago. I recommend a front hitch to anyone who needs to maneuver a trailer in tight spaces.
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This hitch came quickly and I believe was priced fairly for what you get. Unfortunately, as some other have posted, this hitch is intended for my vehicle (1996 Ford E350 RV) but did not fit correctly. I had a problem with the front holes not being spaced far enough apart for the bolts to fit. The rearmost bolts go into a oversized and slotted hole in the underside of the frame so there was no problem with those, but the front holes in the frame have to be drilled out to 17/32" for the supplied 1/2" bolts per the included directions, and I couldn't get the bolts in both sides. The bolt holes in the hitch needed to be approximately 1/4" further apart. Also, there is a relief cut out of the hitch that I assume is to miss a bump on the under side of the frame. This cut out is in the wrong location to miss the bump in the frame. I went ahead and torched the slot for the bolt a little longer on one side and made the cut out for the frame bump bigger on both sides. A little grinding, a little touch-up paint, and back on she went. Had to notch the lower plastic valance just a little bit to clear the receiver, which was expected. Actually had to cut it a lot less than I thought I would. The two safety chain loops sit right under the valance, but I don't for see the need to hook anything to those, so I opted to not hack up the valance at this time. I intend to put a bike rack on the front, and also use the hitch to get drug onto the beach at Pismo from time to time. Hopefully the cuts I made don't weaken the hitch for that purpose. The directions call for this to be a 20 minute install. Granted, I took off the bumper, but even if I hadn't, and the hitch was fitted correctly, I find it hard to believe anybody could get this done in anywhere near that time. As another reviewer said, now that it's on, I'm a happy camper, but it was a little bit of a job to get there.
The hitch is good quality but the hole pattern did not match my 2011 E150 Ford Van. The rear bolts fall in the access hole. I have to drill 3/4 holes in the frame instead of 17/32". I have to remove the whole front bumper because the accesshole is to small for the 1/2 carriage bolt.
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"