Does Edge Insight Programmer Have Ability to Show Engine Oil Pressure
Question:
Hi, I just installed the edge insight cts3 on my 2004 f350 crew cab lariat 6.0, and Im not seeing a pid for oil pressure. I have an oil pressue dummy gauge on the dash that sits right at the middle all the time. I assume that the stock senor is reading a minimum value and giving the ok, rather than actively monitoring the pressure as it changes. Am I correct in this assumption? Is there another way to give real time data to my cts3? Thanks for your help!
asked by: Treven C
Expert Reply:
The Edge Insight CS2 # EP84030 that you referenced can be programmed to display the engine oil pressure or engine oil temperature on your Ford F-350 by going through a few steps.
Looking at the gauge layout screen, press the ENTER button and you will see a gauge location highlighted. Then use the arrows to highlight the particular gauge location you need to modify. Highlight and select NEW PID option, then press enter.
From here use the up/down arrows to highlight a new PID (you might need to scroll a bit or go to the next page to find the EOP and EOT). Doing this should show the new PIDs with any other options you may have changed already. If you don't see EOP/engine oil pressure let me know and I'll check with Edge but in general there isn't a way to add PIDs to a vehicle's PCM as what's there is what's available.
Product Page this Question was Asked From
Edge Insight CS2 Comprehensive Gauge Display - Color Screen
- Performance Chip
- Monitors
- Color Screen
- Yes - California Approved
- Insight
- Edge
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: How to Display Engine Oil Temp and Engine Oil Pressure with the Edge Insight CS2
- Search Results: rv flooring
- Search Results: diamond rv flooring
- Shop: Alpha Systems 4034 Roof Coating for RV Roofs - 1 Gallon
- Shop: Alpha Systems 8010 Adhesive for RV Roofs - White - 5 Gallon
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Video: Mount: Curt Trailer Hitch Receiver on a 2003 Chevrolet Silverado
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2"
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Shop: Lippert Manual Pull-Out Step for RVs - Triple - 7" Drop - 25-3/4" Wide - Steel - 300 lbs
- Shop: B&W Rubber Cover for Stowed Turnoverball
- Q&A: What Parameters Does the Edge Insight CTS Monitor
- Shop: 24x60 etrailer Cargo Carrier for RV Bumper - Steel - Folding - 500 lbs
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Finding the Right Trailer Wiring Harness
- Search Results: trailer hitch
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Shop: Brake Controller
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer hitch ball mount
- Q&A: 7-Way Trailer Plug Adapter or Compatibility with Lance Slide-In Truck Bed Camper
- Q&A: What is the Difference Between the Tekonsha Prodigy P2 and the P3 Brake Controllers
- Search Results: gooseneck hitch
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: brake controller
on Performance Chip
