Where Should Remote Transmission Filter Be Installed On Vehicle

Question

Question:

Before or after cooler? Need to know which location is correct. Going to purchase a remote trans filter kit. Some sites say install on supply side before trans cooler. Others say install after the cooler on the return line back to the tranny. Which is correct? Does it really matter? The fluid pressure will push the fluid through anyway. Before or after.

asked by: Phillip

0

Expert Reply:

When installing a remote transmission filter like part # D13090 on your vehicle, you can install it on either the incoming or outgoing line of the transmission. I have attached a drawing that shows the filter installed on the incoming transmission line.

I called my contact at Derale and they told me it is really up to the individual which side of the OEM radiator they want to put the filter.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

We recommend to check your transmission fluid with your dip stick after installation of the cooler, typically you will need less than 1 pint-quart of fluid to fill the amount of fluid that was displaced. You can try to prefill the transmission cooler…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Isaiah, thanks for reaching out! I recommend the etrailer Trailer Hitch Receiver #e98912 2025 Subaru Crosstrek simply because it has a matte black finish that offers a better look and protection over the glossy black finish we see on the other…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Tim, The ZCI Circuit Protected Vehicle Wiring Harness #119250KIT is compatible with LED lights and has been used as a go to for years for people who have LED trailer lights. The light function is supposed send a tiny bit of voltage from the…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Hi Dave; yes, the Curt #C94WR also fits the 2025 Hyundai Tucson Hybrid. You can actually see it on a hybrid model in the picture I added to this page. The hitch has the 2" receiver you need and a max tongue weight of 525 lbs to handle your bike…

view full answer...

Answer 10

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Where Should Remote Transmission Filter Be Installed On Vehicle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching