Is the Control Adapter Module # HBA-CAM Needed for a 2009 Chevy 3500 With P3 Brake Controller
Question:
2013 Chev 3500 with int. controller, elec/hyd trl brakes. No trl brakes. Installed P3, when using manual level, brake pump stays running. Would Carlisle HBA-CAM solve this?
asked by: Gary
Expert Reply:
You should not need the Control Adapter Module, # HBA-CAM, for the Tekonsha P3 brake controller, # 90195. The P3 is compatible with all electric-over-hydraulic braking systems. The P3 has an automatic leveling sensor, so you should not have to worry about a manual level. You just want to make sure the unit is facing the direction of travel and make sure it is level side to side.
If you are talking about the manual override lever, then the brake pump should stay running when you hold the manual override. The manual override will send a constant signal to the braking system on the trailer to lock the brakes. If the pump stays on after you release the manual override, then there may be a problem somewhere in the wiring.
The first step I would take is to inspect the wiring for the electric-hydraulic actuator on the trailer. Most electric-hydraulic actuators are wired as follows:
One wire goes to a 12 volt onboard battery. Make sure the battery has the proper amp hour rating for the actuator. One wire should be grounded to the negative terminal of the battery. It should not be grounded to the trailer frame. One wire should run to the breakaway switch and one wire should run to the trailer connector and that wire should only have power when the brake controller is activated. Test this wire without the brake controller being activated. If this wire has power, then that is the issue. We will want to determine why that wire has power without the brake controller being activated.
If you can tell me which electric-over-hydraulic system you have, I would be happy to give you more specific wiring information for your unit and more specific troubleshooting steps. Keep in mind, the HBA-CAM is only compatible with Generation 6 and newer HydraStar actuators only.
Products Referenced in This Question
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Product Page this Question was Asked From
Hydrastar Electric Over Hydraulic Actuator Adapter Module for Ford and Chevy Brake Controllers
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Adapters
- Hydrastar
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Correct Gen-Y Pin Box to Replace a MORryde RPB72-1716
- Q&A: Troubleshooting Trailer Brake Module Fault on 2022 Ford F-350 with Factory Controller
- Q&A: Is the Hydrastar Electric Over Hydraulic Acatuator Adapter Module Needed for a 2024 Ford
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Q&A: How To Install HBA-CAM Hydrastar Adapter
- Q&A: Parts Needed To Convert Surge Brake Triple Axle Trailer To Electric Over Hydraulic
- Q&A: Does HBA-CAM Adapter Module for Hydrastar Electric Over Hydraulic Brake Actuators have 2 or 4 Wires
- Article: Adding Electric Over Hydraulic Disc Brakes
- Q&A: Hydrastar Disc Brake Kit For a 2018 Grand Design Momentum Triple Axle Toy Hauler With 7,000LB Axles
- Article: Trailer Wiring Diagrams
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box