Part Numbers: 39510,20127
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
Features:
Specs:
Once the brake controller is installed, you can use the knob on the right side of the unit to adjust the gain (also known as output). Gain lets you set the maximum amount of power that will be applied to your trailer's brakes. You want to set it as high as you can without locking up the brakes. Typically, this setting is only readjusted when you experience changing road conditions or if you switch over from a heavy, loaded trailer to a much lighter, empty trailer, or vice versa.
You can fine-tune the gain by adjusting the sensitivity of the internal sensor using the knob on the left side. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does. A high sensitivity level will get the braking power to your trailer brakes faster and with more intensity so that it doesn't push your tow vehicle forward.
LED Indicator
Keeping with its simple design, the Voyager will not overwhelm you with information. An LED indicator on the top of the unit lights up green to show that your trailer is securely connected to your tow vehicle. The LED indicator will change to red when the brakes on your trailer are activated.
During installation and setup, this light is also used to ensure that the Voyager will be able to function correctly. Proper leveling of the internal sensor is crucial to the operation of this brake controller. When the sensor is level, the LED will change to a shade of orange.
The Voyager is designed to be mounted in your cab at a vertical angle that is between -20 degrees and 70 degrees. The brake controller needs to be horizontally level and parallel to the direction of travel in order to function properly.
To connect the Voyager, hardwire the included harness to your vehicle. For a plug-and-play installation, a vehicle-specific wiring adapter is available for select vehicles. One end of the custom adapter plugs into your vehicle, and the other end plugs into the controller - no hardwiring required.
Once the controller is mounted and connected, you must level the internal sensor. First, set the overall power to the maximum using the knob on the side of the controller. Then, while pressing the tow vehicle's brake pedal, adjust the level knob on the other side of the brake controller (this is the same knob that is used to fine-tune the power output) until the LED monitor is a shade of orange.
Installation Accessories
See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
The Tekonsha Voyager brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Voyager uses a pendulum system to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
California residents: click here
Tow Ready Replacement Plugin Harness for the Tekonsha P3, Voyager, Prodigy, and Primus Brake Controllers. Also works with Draw-Tite Intella-stop Xtreme, Intella-stop Ultra, Intella-stop Digital, and Activator III (5520) brake controllers.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (1374 Customer Reviews)
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
I am very satisfied with the Voyager brake Controller I purchased. It is the easiest unit to adjust that I have ever owned. The controls are easy to adjust and it has worked well with my trailers.
etrailer makes the purchase easy. I have always used Tekonsha Voyagers, and on my new truck (2015 Silverado) I also wanted the convenience of having the plug and play wiring harness. etrailer had exactly what I needed and was very easy to find on the website. Installation was flawless and clean thanks to the good hardware supplied. Very excited to put some trailers behind the truck with the stopping power confidence that comes with the Voyager.
Exactly what I was looking for and needed ! It was delivered very quick . Actually I just ordered a complete wiring harness from you tonight . Your service and follow up is great
The Tekonsha Voyager trailer brake controller works well in my 99 Silverado 1500, which was easy to setup for my trailer. The option to allow for different settings of aggression for the trailer braking has allowed the stopping with different loads to be graceful with the turn of a knob. Decided to install the controller in CD storage with velcro for a nice look. Easy access when in place during use for easy observation and twicking during operation. The wife can assist with the twicking while I am driving. Excellent product!
Completely plug and play installation and works flawlessly, very happy with this unit. I also ordered the exact harness for my 2005 f150 with tow package. Here are a couple of hints that may be helpful. My installation also required a 30 amp cartridge fuse to be installed in the fuse panel in location #105(electric trailer brakes) under the dash on the passenger side. I also installed a relay in location r05 (trailer tow battery charge) but I don't think this is needed for the controller to function. I still had the original trailer brake kit and it had the additional fuse panel instructions and the relay. The owners manual showed where the 30 amp fuse and relay plugs in. You cannot test this unit until a trailer with brakes is connected, ie the led will not light up until it senses a brake circuit.
The drawtite hitch and trailer wiring harness fit great. Instructions were clear and concise. Installation was a breeze. I am ready to tow my little trailer now. As soon as I get the brake controller installed, I will be ready for my big trailer.
This is my second Tekonsha; I had to replace my 10-year old one after I accidentally broke it.
This one is a bit of an upgrade, and is easily able to lock up the disc brakes on my 15,000 lb trailer. Adjusting it properly, I'm able to brake as though there were no trailer at all. Set it, and forget it. It doesn't get any easier than that.
If your truck comes with the tow haul package.... this item is literally plug and play. I had it wired up and all mounted inside of thirty minutes. It's literally 4 wires and the stock system wires are labeled along with the brake contoller. I haven't tested it yet but so far I am thoroughly impressed!
Perfectly wired directly to existing wiring that I had for the previous brake controller I replaced with the, Draw Tite I Command. This will make it a lot easier should I choose to upgrade the unit in the future.
Fantastic customer service from Joshua as well.
Received this yesterday and was able to install it today. Instructions were very easy to follow and the only problem I had installing it was contorting myself to install the bracket. Once I got the bracket in place the rest was a piece of cake. Went for a test drive as the instructions suggested and did have to tweak it a little but it's doing exactly what I expect it to do. I'll be hauling a John Deere Tractor and wanted to make sure the brakes on the trailer worked.
Class iii Draw Tite trailer hitch:
This part was quick and easy to order and I received it sooner than expected. My mechanic said the installation was easily accomplished and looks great on my car. I would not hesitate to order from etrailer again!
Griff M.
6/21/2023
The product has worked well. I have had no problems with it.
Purchased this as part of all parts required to convert 1996 Jayco over to electric brakes. Very happy with results. Surprised to see after winter in storage that the battery supply still shows full charge.
Installed in my 2018 Silverado Custom. I ordered the additional wiring harness and the install took less than thirty minutes. Plug and Play at its simplest. Thank You etrailer.
Hard to adjust. Had tech at rv place adjust still grabby. Should have got more modern controller
I installed the Curt gooseneck on my 1993 GMC 2 Wheel Dr. 2500 truck. All the components have tight tolerances. It took me eight hours. With a socket and the wrench. Laying on my back. I did have to cut the wheel well lip about 3/8 of an inch off because I could not get that front angle bar to slide in without hitting it, no way around it unless you lift the bed up and I wasn’t going to do that!!. You have to cut it.instructions do not state that. I’m very happy with the Hitch, it is definitely stout! I did have to make a notch on the outside brackets to go over my airbag bolt. I also had to remove the support bracket on the inside of the frame for the airbag and the crossmember for the spare tire to get the front angled bar in.
This was an easy install on my 2019 GMC truck using the appropriate wiring adapter. Instructions for setting up the control were clear. After a few adjustments my trailer brakes worked as they should. Minor adjustments of the controller are needed from time to time, but overall the controller is reliable. Good value.
Plug it in and voila!
As always, etrailer delivers. Part was on time and a perfect match for the brake controller. What you don't get from Amazon is the technical support on how to install or use the equipment purchased from etrailer. That's why I keep coming back!
The correct items that fit properly were delivered in a timely manner.
We just installed this in our truck and install was fast and easy with adapter cable we ordered. and set up of controller was very simple.
These guys are great they had the installation kit it came with everything you need and even had a video for my specific vehicle to install the brake controller and wire in a 7 pin trailer plug
If you don’t have factory brake controller the etbc7 is an amazing kit they have comes with everything I mean everything
Tim
6/26/2021
Everything has been excellent e trail has the right products and they fit just like they say
My truck was stolen and wrecked. I was able to retrieve the Tekonsha Brake controller from under the Dash board before it was hauled to the salvage yard, but not the wire harness. I was ale to order a replacement harness from eTrailer and reinstall the controller in my new truck. I had no problems at all. Thank you eTrailer for the great support.
Don
3/9/2022
Still works perfectly after one year. Actually, I been using this Controller for well over a year. I just reinstalled it in my new truck a year ago.
The product was easy to install with the help of the F-250 adapter. I followed the direction and the product worked just as it was advertised from etrailer.com. If I had to give the Tekonsha Voyager Trailer Break Controller a star rating from 1-5, I would give it a 4.5.
Works as intended, but the plug on the back of the controller is a loose connection. Sometimes I would go to brake and find that I had no trailer brakes because the controller lost power. After a wiggle it would start to work again. I was able to shave the Molex plug a bit and now I don't have any problems with it.
Sierra K.
7/19/2021
Thank you for your review. I have not heard of that problem. I would have used some electrical tape.
Easy installation and seems to be a great product. I also used the harness for my 07 new body Silverado for a easy install. Videos are a great help as well . I will purchase all of my trailer and RV needs from ETrailer from now on.
Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Michael
2/19/2024
After 1 yr and many trips this product has more than exceeded my expectations. Would definitely recommend it to anyone