Great for cars and trailers with either LED or incandescent bulbs, this kit converts your vehicle's lighting system to match your trailer's. It includes a 4-way flat, wire taps, and a power wire that pulls power directly from your battery.Use a circuit tester on the plug terminals once the harness is installed to make sure everything's working. There's nothing worse than figuring out that you have a bad ground or a faulty connection right before you're about to hit the road.
Built to last, this kit, made with surface-mount technology, converts your vehicle's lighting system to match your trailer's. It includes a 60" 4-way flat harness, wire taps, and a power wire that pulls power directly from your battery.Use a circuit tester on the plug terminals once the harness is installed to make sure everything's working. There's nothing worse than figuring out that you have a bad ground or a faulty connection right before you're about to hit the road.
If your bolt-on Dexter Fortress cap has been damaged but the gasket and install bolts are in good condition, this is what you need. It is the complete cap without the gasket or install bolts. Save yourself some money and just replace what you need.Get Your Hub Sealed Again: Replacement bolt-on cap restores the damaged outer cap when the rest of the setup is still usable. Know What You Need for Install: Replacement includes the cap only; gasket and mounting screws are not included. Black Finish Matches Existing Caps: Blends with your existing Dexter Fortress caps for a consistent look.
Built to last, this kit, made with surface-mount technology, converts your vehicle's lighting system to match your trailer's. It includes a 60" 4-way flat harness, wire taps, and a power wire that pulls power directly from your battery.Use a circuit tester on the plug terminals once the harness is installed to make sure everything's working. There's nothing worse than figuring out that you have a bad ground or a faulty connection right before you're about to hit the road.
Replacing a rooftop RV accessory is a lot easier when the sealing materials are already in 1 box. This install kit includes butyl tape, lap sealant, and a putty knife so you can seal rooftop accessories without hunting down extra supplies.Penetration Weather Protection: 2 tubes of white self-leveling lap sealant seal around rooftop penetrations. Prep Tool Included: Putty knife supports installation and sealant application preparation. One or More Installations: Sealing material covers one or more rooftop accessory installs, depending on size.
2,500-lb Load leveling capacity. Custom helper springs install above your vehicle's rear factory leaf springs to reduce sway and prevent sagging when towing or hauling heavy loads. Includes bolt-on installation kit.Please consult the installation guide. Do not install on vehicles with composite (plastic) leaf springs. Hellwig Leaf Spring Comparison
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 427-1/2 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape White color Made in the USA Specs: Membrane specs: Dimensions: 45' long x 9-1/2' wide 427-1/2 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 380 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape White color Made in the USA Specs: Membrane specs: Dimensions: 40' long x 9-1/2' wide 380 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 237-1/2 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape White color Made in the USA Specs: Membrane specs: Dimensions: 25' long x 9-1/2' wide 237-1/2 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 190 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape White color Made in the USA Specs: Membrane specs: Dimensions: 20' long x 9-1/2' wide 190 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 380 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Beige color Made in the USA Specs: Membrane specs: Dimensions: 40' long x 9-1/2' wide 380 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
This universal wiring kit lets you install an electric brake controller (sold separately) in your vehicle and a 7-way connector for your trailer lights at the same time. Plugs into the existing 4-way on your vehicle.Extra-long vehicles: If you drive a crew cab, extended cab with long bed, cargo van, or extended-length SUV, extra wire (ETBCXW - sold separately) will make installation much easier. Wiring Diagram for Trailer Brake Controller Installation
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 237-1/2 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Beige color Made in the USA Specs: Membrane specs: Dimensions: 25' long x 9-1/2' wide 237-1/2 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Includes everything you need to install your new roof membrane (sold separately) - 2 gallons of adhesive, 6 tubes of self-leveling sealant, 1 tube of non-sag sealant, and 5 rolls of butyl tape for a strong adhesion to your RV rooftop.Features: Installation kit includes everything you need to install your new roof membrane Components work with surfaces such as wood, metal, glass, and fiberglass Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays White, weather-resistant sealants are paintable Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (6) 10.3 oz Tubes of 1021 self-leveling sealant (1) 10.3 oz Tube of 1010 non-sag sealant (5) 30' Rolls of butyl tape Specs: Adhesive specs: Coverage: 160 - 200 sq ft per gallon 1-Year limited warranty Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Butyl tape specs: Dimensions: 3" wide x 50' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F
Includes everything you need to install your new roof membrane (sold separately) - 2 gallons of adhesive, 15 tubes of self-leveling sealant, 2 tubes of non-sag sealant, and 6 rolls of butyl tap for a strong adhesion to your RV rooftop.Features: Installation kit includes everything you need to install your new roof membrane Components work with wood surfaces such as wood, metal, glass, and fiberglass Alphabond tape adheres instantly and seals upon itself TPO facer resists damage caused by UV-rays White, weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-levelling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Specs: Adhesive specs: Coverage: 160 - 200 sq ft per gallon 1-Year limited warranty Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 332-1/2 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape White color Made in the USA Specs: Membrane specs: Dimensions: 35' long x 9-1/2' wide 332-1/2 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 285 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Gray color Made in the USA Specs: Membrane specs: Dimensions: 30' long x 9-1/2' wide 285 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Includes everything you need to install your new roof membrane (sold separately) - 2 gallons of adhesive, 15 tubes of self-leveling sealant, 2 tubes of non-sag sealant, and 6 rolls of butyl tap for a strong adhesion to your RV rooftop.Features: Installation kit includes everything you need to install your new roof membrane Components work with wood surfaces such as wood, metal, glass, and fiberglass Alphabond tape adheres instantly and seals upon itself TPO facer resists damage caused by UV-rays Beige, weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-levelling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Specs: Adhesive specs: Coverage: 160 - 200 sq ft per gallon 1-Year limited warranty Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F
Replacing an RV roof goes a lot smoother when the main sealing and bonding materials are already in one kit. This installation package includes adhesive, butyl tape, Ultra Sealant, and primer designed for EPDM+ and similar roofing systems.Highlights Roof Membrane Installation: Sealing and bonding materials come in 1 kit for roof replacement work. Membrane Bonding: 2 gals. of water-based adhesive support roof membrane installation.
Includes everything you need to install your new roof membrane (sold separately) - 2 gallons of adhesive, 6 tubes of self-leveling sealant, 1 tube of non-sag sealant, and 5 rolls of butyl tape for a strong adhesion to your RV rooftop.Features: Installation kit includes everything you need to install your new roof membrane Components work with surfaces such as wood, metal, glass, and fiberglass Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Gray, weather-resistant sealants are paintable Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (6) 10.3 oz Tubes of 1021 self-leveling sealant (1) 10.3 oz Tube of 1010 non-sag sealant (5) 30' Rolls of butyl tape Specs: Adhesive specs: Coverage: 160 - 200 sq ft per gallon 1-Year limited warranty Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Butyl tape specs: Dimensions: 3" wide x 50' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F
XTRM Ply offers unbeatable heat reflection with a 109 SRI, 20 percent more tear resistance, and double the puncture strength. No treatments needed - won't chalk, streak, or spot. Installs easily even over tricky transitions. Built to flex.The adhesive settles in over time for a hold you can trust long after the install is done. Easy Application, No Guesswork The adhesive spreads easily with a roller or brush. Clean the surface, lay it down, and get full contact without a fight.
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 285 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Beige color Made in the USA Specs: Membrane specs: Dimensions: 30' long x 9-1/2' wide 285 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Replace or upgrade the roof of your RV with this premium roofing membrane. Single-ply membrane is lightweight and flexible. Resists mold, algae, fungus, and damage caused by UV rays. Measures 190 sq ft. Includes adhesive, sealant, and butyl tape.Features: Roofing membrane replaces the roof of your RV Single-ply membrane is lightweight and flexible 10% Thicker, 220% stronger, and stretches 500% longer than PVC roofing Superior Superflex material resists punctures, tears, mold, algae, and fungus Textured surface provides better traction when working on your roof Alphabond tape adheres instantly and seals upon itself TPO facer resists the damage caused by UV-rays Weather-resistant sealants are paintable Non-sag sealant holds its shape on uneven or vertical surfaces Self-leveling sealant is used for replacing rooftop accessories after installation Kit includes: (2) 1 Gallon buckets of 8011 adhesive (15) 10.3 oz Tubes of 1021 self-leveling sealant (2) 10.3 oz Tubes of 1010 non-sag sealant (6) 30' Rolls of butyl tape Beige color Made in the USA Specs: Membrane specs: Dimensions: 20' long x 9-1/2' wide 190 sq ft Adhesive specs: Coverage: 160 - 200 sq ft per gallon Self-leveling sealant specs: Raw material base: butyl rubber Viscosity: 80,000 - 200,000 centipoise Specific gravity: 1.25 - 1.35 Solids: 77% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 293 grams per liter Non-sag sealant specs: Raw material base: butyl rubber Viscosity: 800,000 - 1,200,000 centipoise Specific gravity: 1.35 - 1.45 Solids: 82% Coverage: 380 lineal feet per gallon Service temperature range: -65 F - 250 F Application temperature range: 5 F - 120 F VOC content: 259 grams per liter Butyl tape specs: Dimensions: 3/4" wide x 30' long Softening temperature: 240 F - 250 F Viscosity: 13,000 - 20,000 centipoise Tensile strength: 4,000 - 5,000 psi Shear strength: 55 - 60 psi Service temperature range: -20 F - 200 F Application temperature range: -10 F - 160 F 15-Year limited warranty
Filters
