!V70  x   >   1972  x   >  

Do you have this or a similar product in stainless steel? I am attaching to an aluminum trailer bed. Brophy D-Ring Tie Down Anchor - Bolt-On - 4-7/8 Wide - Recessed Mount - 1,600 lbs Item # RR05 | Hey Mark, so we don't have a stainless steel...

Current Dexter brake drum/hub is marked as follows: 8-249, MTA 1, 10inch on a 3,500 LB AXLE. Please let me know what part number I need to order to replace one of my brake drum/hubs on my Load Trail carhauler trailer with tandem axles with...

which airbags fit this truck? | For your 1972 Ford F-350 2WD dually we have the Firestone kit part # F2071 as a confirmed fit that would work well. We confirmed this with Firestone. |

left to right hole spacing with hitch configured for 34inch frame | The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front...

Will this system work on a 1972 Chevy Longhorn ? | The Brophy Clamp On Camper Tie-Downs # HSWB are designed with Ford trucks in mind so for your older 1972 Chevy pickup you'll have better luck with the universal Brophy tie-downs: - Brophy...

1972 chev c10 pickup - Firestone riderite air bags shows not compatable with hitch in bed. Whats with that??? Considering this product for pulling my 5th wheel. Why is it not compatable with hitch in bed?? Thanks | For your 1972 Chevy C10...

Hi, I have a 1972 Chevrolet K10 4WD truck. It has a 307 V8 engine w/ 3 speed on the column. It has leaf springs on the front and rear. It also has a standard step bumper not a bumper. I believe the shackles are 4 to 6 inches from the end...

Does Tekonsha make a time delay brake controller that uses the same wiring harness plug as the P3? I have installed a P3 and can’t get it to work right so want to go back to a more basic and simple to use controller and hoping Tekonsha makes...

I have a 2009 F-150. Is this cover big enough? Thanks in advance. | The Snoblock Snow and Ice Windshield and Wiper Blade Cover - 70" Wide x 39" Tall # 288-06603 will be wider than your 2009 Ford F-150 windshield and will work very well. ...

Do you make a trans pan cooler for the late mobel Dodge 904? If so what is the part number please? I have been looking on-line with NO luck......I have a 1972 Dodge Dat with a 318 and a 904 tranny......Thanks! | I spoke with my technical contact...

Do you have dimensions of this spring. This is for a custom install. | I checked with Sumosprings and the # SS65FR and the dimensions are 5 inches tall by 4 inches in diameter without the spacer. |

My 1972 Ford F250 is a Flatbed truck. Do you sell a trailer hitch for my truck? If you do I would like to buy one and everything else that goes with it. Thank you very much. | We do offer trailer hitch options for a 1972 Ford F-250 but as...

Im looking for a class 5 hitch with 2inch receiver for my Winnebago. There is no ion and the specs are hard to find. The Frame rails C-channel outside to outside at the rear are 34 inches apart, and are 1.75 wide at the rear section. Welded...

i have a step bumper on my 1972 k-20 so i will need 1 that will clear my bumper !! | I do see that a deepdrop rear step bumper was offered on your 1972 Chevrolet K-20 pickup. If this is what you have the Curt 3-Piece Trailer Hitch Receiver...

Im looking for a t-connector wiring harness for my 1972 vw bus campmobile. | I do have a trailer wiring harness option for you to consider however, there are no t-connector wiring harnesses for your 1972 Volkswagen Bus Campmobile. In order...

I really like the overall design and materials usage with this vent. Ours recently gave it up with the latest hail storm. The cover has nice metal 4 point hinge configuration. Will these metal hinges work with our plastic hinges that are molded...

Hi, Im looking for a WD hitch with some sway control that does allow backing up and looking for a little guidance. My tow vehicle is a 1972 Chevy Blazer tow capacity 5500 lbs I am presently towing a 1996 Coleman Niagra. I dont have solid weights...

We are in search of a spare for our camper. The tire reads 7.00x15lt on a 17 inch rim. It is 4 bolts on 9.44. Do you have anything thing that would work with this? | Since your tires are 7.00X15LT, the "15" in that tire size means that they...

will this 20002 bumper fit on a 1972 chevy pickup? and if so what bracket kit do I need? thank you | You can install the Westin Fey bumper on your 1972 Chevy K-20 with the part # 20002-92500. This comes with the bumper you are looking...

I have an old 1972 international scout II with a factory installed class II hitch. I have no wiring for a four pole electrical hook up. I did some searching on your website and saw that C58044 may be compatible with my Scout wiring. Is it? Do...

Looking at bumper 21002-92230. Those are good pictures but my mount is a little different. It is a 72 f-250. I can email pictures of it. What I am looking for is what your bumper has for mounts without the kit brackets. Im thinking I may be...

will the bestop soft door fit with my hardtop thanks Kent. | Yes, I checked with Bestop and the Bestop 2-Piece Soft Doors # B5177415 have been confirmed to fit your 1972 Toyota FJ40 with a hard top. I attached a set of installation instructions...

need a tow hitch for a 1972 c-20 long bed with original bumper which hitch do i buy ,need help. | The Curt Trailer Hitch Receiver part # 13028 is a confirmed fit for your 1972 Chevrolet C-20 with the standard bumper. It will fit both the 6 and...

will this bumper fit a 72 chevy c-10 pickup? | I have a great alternative bumper that will fit your vehicle. Unfortunately, the Westin Fey Diamondstep Rear Bumper - Chrome # 71000 is not manufactured to fit your 1972 Chevy C-10. However, I confirmed...