Solution to Replace 8k Kodiak XL NevR Lube Hub Drums
Published 06/20/2022
Products Featured in This Question
Question:
I need to replace my Kodiak 13-inch integrated brake rotor and NevR Lube hub HRCM-133-8XL with a Dexter 008-402-91 NevR Lube hub and slip over rotor. Both the Kodiak and Dexter have 5/8-inch bolts. My question is about the offset or distance from the back side of the slip over rotor KR13858D to the face of the rotor where the wheel connects. Is it the offset or distance from the back of the KR13858D rotor to the face of the rotor the same distance as the Kodiak HRCM-133-8XL? Also, is there a size difference between the KR13858D and the K71-631-00? The K71-631-00 appears to be more offset.
asked by: Darryl B
Expert Reply:
Yes you can go the route you mentioned. You'd need to install an idler Dexter 8k Nev R Lube hub with part # 004-402-90 on your spindles and then you could use a slip on kit like the part # K71-635-90 and you'd be set.
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Gooseneck Hitch
- Q&A: Replacement Hub/Rotor Assembly Kit for Kodiak HRCM-133-8XL Hub/Rotor
- Shop: Stake Pocket Tie-Down Anchor - Black Powder Coat - 2" D-Ring - 1,600 lbs
- Search Results: 13397
- Shop: Unitized Oil Seal
- Shop: 50MM Nev-R-Lube Bearing for 8,000-lb Dexters - Qty 1
- Q&A: Proper Location of Inlet and Outlet Lines When Installing Plate-Fin Transmission Cooler
- Shop: Kodiak 13" Hub and Rotor - 8 on 6-1/2 - Dacromet - 1/2" Bolts - 7,000 lbs
- Shop: B&W Ball and Safety Chain Kit for Ford, GM, Chevy, and Nissan Titan XD Underbed Gooseneck Hitch
- Shop: Fifth Wheel Hitch
- Shop: Dexter Trailer Brake Drum for 9,000-lb to 10,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Non-ABS
- Shop: Oil Seal
- Search Results: 10~51
- Q&A: Determining Replacement Hub And Bearings For Dexter P-12 SLR Trailer Axle
- Search Results: 10k brake drum
- Shop: Transmission Cooler
- Shop: RV Interior Lighting
- Shop: RV Exterior Lighting
- Search Results: aps4
- Search Results: ramp door spring
- Search Results: generator tray
- Search Results: stake pocket d~rings
- Q&A: Do Nev-R-Lube Bearings Last a Long Time
- Q&A: Side Marker Camera Recommendation For A 2022 Jayco 166FBS That Is Prepped For Side Cameras
- Q&A: Trailer Light Replacement Lens for Light Marked SAE-A-P2-DOT-02
- Q&A: Replacement Marker Lights for Furrion F0S04TDE-RD/SY Lights
- Video: Review of Furrion Replacement Vision S Passenger Side Camera - FR28NR
- Video: Review of Furrion Replacement Vision S Driver Side Marker Light and Bracket - FR66PR
Darryl B.
6/20/2022
I need to replace my Kodiak 13-inch integrated brake rotor and NevR Lube hub HRCM-133-8XL with a Dexter 008-402-91 NevR Lube hub and slip over rotor. Both the Kodiak and Dexter have 5/8-inch bolts. My question is about the offset or distance from the back side of the slip over rotor KR13858D to the face of the rotor where the wheel connects. Is it the offset or distance from the back of the KR13858D rotor to the face of the rotor the same distance as the Kodiak HRCM-133-8XL? Also, is there a size difference between the KR13858D and the K71-631-00? The K71-631-00 appears to be more offset.