Need Frame for Ventline Screen VD0434 for RV Roof Vent

Question

Question:

Hi! I see the answer for manual open however my screen has a circle cutout for a black dial knob to open the vent cover. Mine are sun brittle and need to be replaced. Can you please advise on version with twist knob opening? Thanks very much!

asked by: Deb

0

Expert Reply:

Based on the part number of VD0434 that you mentioned the correct screen frame you'd need would be the part # BVC0573-41.

expert reply by: Jameson C

0

Answer 1

There are two possible options to replace your VD0434 depending on the color you're looking for. We have the #BVD0434-41 which is polar white and the #BVD0434-31 which is birch white.

view full answer...

Answer 2

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement lid #BVD0449-A01, and the replacement ceiling garnish #VA0445-28 all available for…

view full answer...

Answer 3

I've confirmed with Ventline that the #BVD0434-31 screen is the correct replacement screen for the VD0434 roof vent in your truck camper.

view full answer...

Answer 4

The direct replacement for your Ventline screen with model number VD0434 is #BVD0434-31 (birch white) or #BVD0434-41 (polar white). This is compatible with Ventline Ventadome roof vent models V2092, V2110, V2094 and V2119. However, if you're…

view full answer...

Answer 5

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Answer 6

If you're looking for the garnish ring that screws into the ceiling of the trailer then you'll need part #VA0445-29 for a birch white finish. If you're looking for the inner frame and screen then you'll want part #BVC0573-31.

view full answer...

Answer 7

Sounds like you are looking for a replacement screen frame which for that you'd need the #BVC0573-32 for if your vent is a powered lift vent or part #BVC0573-31 for if it is a manual lift. Then for the garnish what you would need is the part…

view full answer...

Answer 8

I do have a replacement screen available for the Ventline Ventadome VD0433 Trailer Roof Vent that you have on your trailer but they do not make a non-removable version that will work for you. Instead, I recommend replacing the screen with part…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Need Frame for Ventline Screen VD0434 for RV Roof Vent

Products Featured in This Question

Continue Researching