Longest Roof Rack for Lance 855S Truck Camper

Question

Question:

Lance 855 s need 96 inch cross bars Need to have cross bars for 2021 Lance 855S truck camper to mount Thule box.

asked by: Julie N

0

Expert Reply:

For your application I recommend the 79" Long Rhino-Rack Vortex Crossbars # RRVA200B-2 and then with 2 kits of the Track Mount RLTF Legs for Factory Roof Rack Tracks # RLTFMV. This is one of the longest bars we have for a setup that fits the OEM rails on your camper.

expert reply by: Jon G

0

Answer 1

I went out into our showroom and measured the dimensions of a set of discontinued Thule square load bars and found that they are 7/8 of an inch by 1-1/4 inches. This is identical to the Inno square bars like #INB137.

view full answer...

Answer 2

The MB Sturgis Propane Pigtail - Type 1 x 1/4" Male Inverted Flare - 1' #100575-12-MBS is the standard pigtail for your Lance Camper. It will connect to your propane tank and then to your regulator. I recommend the Camco Automatic Changeover…

view full answer...

Answer 3

The longest crossbar we have is the 80" Yakima CoreBar Crossbar #8880656 but for 8' you'd need a 96" crossbar. Usually when people mount a roof rack system to a truck bed camper like your Lance they will offset it to it's easier…

view full answer...

Answer 4

I would be happy to! We have quite a few options for TRUE Frame Mounted Torklift camper tie downs for a 2015 Ford F-250. I have listed our entire selection below because there are several different ones depending on what model and accessories your…

view full answer...

Answer 5

We do have a solution for you, however, you will not be able to power reverse lights on a trailer with a 4-pin trailer connector. The reverse lights on a trailer must receive power from the reverse lights on the tow vehicle. To do this, you will want…

view full answer...

Answer 6

For your Lance 855s Camper with standard tracks I recommend the Rhino-Rack Quick Mount Legs for Vortex Aero Crossbars - RTC and RT Roof Rack Tracks - Qty 4 #RRRLT600 and then crossbars like the Rhino-Rack Vortex Aero Crossbars - Aluminum - Black -…

view full answer...

Answer 7

Since the 7-way round pin plug is obsolete, your best bet would be to replace the connector on your camper with the common 7-way blade style connector. You'd remove the existing plug on your slide in camper, and replace it with #A7WCB. You could…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Longest Roof Rack for Lance 855S Truck Camper

Continue Researching