Tonneau That Fits 2016 Ford F-350 with Toolbox Flush with Top of Bed Rails

Question

Question:

I have a fuel tank/tool box mounted that comes even with the truck side rails. Will the cover hardware clear the tank?

asked by: Joseph S

1

Helpful Expert Reply:

You'd need a tonneau cover that sits up higher above the top of the bed rails like the Bestop EZ Fold part # B1613501 as the Truxedo you mentioned would not sit high enough, and also worth mentioning is that even if you could install and roll up the cover it would interfere with the box opening. The EZ Fold instead folds up thinner to allow the lid to open.

expert reply by: Jameson C

1

Tonneau Cover That Can Fit Above Truck Bed Toolbox
(click to enlarge)

Answer 1

The SolidStep Manual Fold-Down Steps part #LC791574 would be correct for your Grand Design Reflection 337RLS as it works with doorways between 28" - 30" and entry height from 35" - 44". This is an excellent upgrade for your RV and…

view full answer...

Answer 2

The correct replacement bearing kit for a 6,000 lb Dexter axle is the following: - Bearing Kit #BK3-100 This comes with the correct replacement bearings, races, and seal for one hub, so you'd need a quantity of two bearing kits for one axle.

view full answer...

Answer 3

Hey Bob, I checked out your WFCO WF-9855 and it is a 55 amp charger that is NOT compatible with lithium batteries so what you'd want instead is the Progressive Dynamics Charger part #PD79RR that is similarly rated at 60 amps and does have a…

view full answer...

Answer 4

Despite what the manufacturers of these equalizers say, the axle/wheel spacing isn't the right way to figure out the best fit for upgraded equalizers, including the MORryde CRE3000. The wheel spacing is more of a guideline, so to determine the…

view full answer...

Answer 5

I have a perfect solution for you! In order to attach the magnetic Blazer Amber Warning Light Bar #C4850AW to your aluminum body Ford F-250 I recommend using the Buyers Products Magnetic Mounting Plates #3378895404. These self adhesive magnetic mount…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Hey Willyd, it looks like you have a 7-way round connector which is a bit more rare and for that we only have a 7-way to 4-way adapter like the part #47405. Does your trailer with a 5-way actually use the 5th circuit? If so what is it for?

view full answer...

Tonneau That Fits 2016 Ford F-350 with Toolbox Flush with Top of Bed Rails

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching