What Type of Window Does Lippert Thin Shade Window Shade # LC786037 Fit

Question

Question:

Can you install a Lippert Slim Shade unit in a Lippert RV door that currently has no glass in it?

asked by: Jay Y

0

Expert Reply:

The only type of window that the Lippert Thin Shade Window Shade # LC786037 is going to fit is one that is "thin shade read" which will be printed on the top of the window like you can see in the attached picture. If you don't have glass in a window you most likely don't have what this is capable of.

expert reply by: Jameson C

0

thin shade ready
(click to enlarge)

Answer 1

In regards to the Lippert Thin Shade Window Shade for Thin Shade Ready LCI Entry Doors part #LC786037, you can adjust the cord tension so you don't have issues with the blinds falling on their own. I have attached these instructions for you…

view full answer...

Answer 2

A replacement hardware kit that includes brackets is indeed available for the Stromberg Carlson Bunk Ladder as part #2460.

view full answer...

Answer 3

Thank you for including a photo of your ladder's broken hook. We can help you! We offer a Replacement Installation Hardware Kit #2460 that works with Stromberg Carlson and other brands of RV ladders. You will notice that the shape of the larger…

view full answer...

Answer 4

We have ladder hardware like you are looking for as part #2460. This gives you a bracket to attach to the side of the bunk and hooks for the ladder to attach to as well. This is the same hardware that comes with the part #LA-460.

view full answer...

Answer 5

We do not have any set screws for curtain rods, however we do have the Snap-In RV Curtain Carriers #37281455 which you could use instead to secure and adjust your curtains. This kit contains 14 carrier and easily installs onto some snap tape like the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

What Type of Window Does Lippert Thin Shade Window Shade # LC786037 Fit

Continue Researching