What Bearings, Races and Grease Seal does Kodiak K2HR10A11RERR 10K Disc Brake Kit Use

Question

Question:

Can you tell me the bearing sizes in this hub?

asked by: Jay G

0

Expert Reply:

The Kodiak # K2HR10A11RERR 10K disc brake kit uses a # 28580 inner and a # 25580 outer bearing along with a # 91030 grease seal. The inner race is # 28521 and the outer is # 25520.

expert reply by: Mike L

0

Answer 1

The Dexter Trailer Hub and Drum Assembly #8-219-4UC3 fits a standard #42 Spindle #TRU57FR. While the Dexter Trailer Hub and Drum Assembly #8-219-4UC3-EZ fits a E-Z Lube #42 Spindle #TRU37FR. You will need to select the appropriate assembly based on…

view full answer...

Answer 2

The difference really comes down to brand recognition, price, and warranty, but apart from that they are very similar. Dexter is a leading brand and people know they are getting quality, hence the higher price. They Dexter also do have a 5-year…

view full answer...

Answer 3

The part number 297697 is for a Dexter 7K axle. There is a full bearing kit for this. It's part #BK3-200. It includes the bearings, races, and seals. Of course, this is not a definite replacement as I could not find exact numbers for your axles.…

view full answer...

Answer 4

The correct replacement brake shoes for a 2013 Keystone Montana Mountaineer with Dexter 7,000 lb Nev-R-Adjust Braking Assemblies is going to be the Replacement Shoe and Lining for Nev-R-Adjust 12" x 2" Electric part #K71-675 for the left…

view full answer...

Answer 5

The Lippert Components Polarity Reversing Solenoid by Trombetta #LC118246 that you referenced is the correct replacement. If you check out the picture I attached you'll see that the numbers you listed match the decal on the side of this. By the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

What Bearings, Races and Grease Seal does Kodiak K2HR10A11RERR 10K Disc Brake Kit Use

Products Featured in This Question

Continue Researching