How Far Apart Are the Top and Bottom Bracket on the K-Source H3661 Mirrors

Question

Question:

Hello Can you tell me the measurement from the top holes to the bottom holes center to center. Hopefully it’s around 9 1/4. If so I would like to order one for both sides

asked by: Clint J

0

Expert Reply:

I was able to confirm with my contact at K-Source that the mounting brackets on the # KSH3661 are approximately 9" apart from top to bottom. Additionally the mounting holes on the top bracket are 3-3/4" apart
and the bottom are 2-5/8" apart.

expert reply by: Erik B

0

click to enlarge

Answer 1

The top mounting hole measured center to center to the bottom mounting hole is 18". The overall length of the arm is 19 1/4". The mirrors are going to be a bolt on installation, it may require drilling if existing holes are not present. All…

view full answer...

Answer 2

The bolt holes on the top bracket of the CIPA Universal Door-Mount Replacement Mirrors #CM45000-2 are 3-13/16" apart center to center. I have attached a few diagrams showing the measurements for your reference.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Hey Eric! For air bags I recommend going with Firestone. They make the most durable and reliable air bags for your 2024 F-250. If you don't mind using your phone to control the air compressor you can use the Firestone Ride-Rite Air Bags w/ Easy…

view full answer...

How Far Apart Are the Top and Bottom Bracket on the K-Source H3661 Mirrors

Product Page this Question was Asked From

Continue Researching