Looking for Trailer Hitch for 1999 Chevy Astro That Doesnt Extend Past Bumper
Question:
I have a 1999 Chevy Astro Cargo Van. Im looking for a pic or specs that show a side-view of the hitch. I had a Draw- Tite on my 88 Astro and the receiver stuck out from the bumper by about 3/4....my shins got all bruised and I finally became so frustrated that I removed the Hitch and gave it away on Craigslist. Taking this into consideration, do you know which hitch might be best for my van to avoid this phenomenon?
asked by: Paul
Expert Reply:
I'd recommend going with a Class III hitch like the Curt # C13035. A Class III hitch with a 2 inch receiver will allow both a higher capacity than a Class II like the # 90231, but will also have a much better selection of hitch mounted accessories available, such a cargo carrying trays or bike racks. A Class III is usually not any more expensive than a Class II, so there's really no reason not to go with the alternative that would allow you more options and flexibility.
As you can see from the provided photo, the receiver tube does not extend past the face of the bumper, so your shins will be perfectly safe.
If you'll be towing with the hitch, you'll need a few additional accessories. For trailer wiring, use # C55411, # 2753 for a ball mount and for a trailer ball, use # 19260 for a 1-7/8 or # 63845 for a 2 inch ball. For a hitch pin, use # PC3.
You can see an installation video by using the provided link.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Curt Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"