Are Pro Series Bolts Grade 8 for Mounting Demco Lunette Ring

Question

Question:

Our the bolts in product #PS024202 grade 8 bolts? Also, what is the torque setting for these nuts supplied with the bolts? I will be attaching DM09557-95 to a C-channel using these bolts. Thank you.

asked by: Nathan

0

Expert Reply:

Yes, we the Pro Series Mounting Bolts for Adjustable-Channel Couplers # PS024202 are Grade 8 bolts. These are exactly what you will need to mount the Demco Lunette Ring # DM09557-95 you referenced to the Demco 6-Hole Adjustable Channel Bracket # DM59602.

I have added a link to video reviews of each of these products for you to check out.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Larry! If your DA66B is the drum brake model the Demco Hydraulic Brake Actuator #DM72VR is the direct replacement. Since you were asking about the Hydraulic Brake Kit #AKFBBRK-7-D as well I'll assume that is correct. The brake mounting…

view full answer...

Answer 6

Hey Alan, welcome back! The Velit Diesel RV Heater for Camper Van #VE66QV is capable of heating a trailer that size. However, a major factor in how effective it is will be the insulation on the trailer. Even with adequate installation it may be…

view full answer...

Answer 7

Hey John, thanks for reaching out. You will want to use some 1/2" grade 5 bolts and locknuts for mounting the Demco Channel Tongue Trailer Coupler #DM15945. Since the current coupler uses only 2 bolts, you will be fine to use two bolts with the…

view full answer...

Answer 8

If your boat trailer has a 3" wide tongue then yes the Demco 5-Position Adjustable Channel Bracket #DM13867-52 will work great. If not, feel free to let me know what you have and I can look and see what we have.

view full answer...

Answer 9

It really depends on your setup, if the safety chain loops on your tow vehicle are spaced far apart then you will need more slack to make a tight turn then if they were closer together. What I would recommend you do is connect your trailer to your…

view full answer...

Answer 10

First I want to make sure you verify your channel mount for the Demco Trailer Coupler #DM14040-81 has a 21K or larger capacity as often times they are less like the Demco #DM15349-52 which often times people look at and think it is a channel mount…

view full answer...

Answer 11

The Demco Adjustable Channel Trailer Couplers like the 21K #DM14040-81 use 5/8" diameter bolts for attachment to the adjustable channel, so you could potentially replace them with 5/8" locking pins like etrailer.com #e98881. Please keep in…

view full answer...

Are Pro Series Bolts Grade 8 for Mounting Demco Lunette Ring

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching