Where Is Brake Controller Install Port for 2003 Ford F-150

Question

Question:

Where will I locate the plug on my 2003 Ford F-150 4x4 lariat

asked by: Warren C

0

Expert Reply:

To install the Tekonsha brake controller part # TK90160 on your 2003 Ford F-150 will require you to use the install harness part # 3035-P. I attached an install video that shows this connector installing a brake controller in a similar 2005 Ford F-150 as well as a picture of where you'll find it under your truck's dash.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hi Daniel; thanks for the question and I can absolutely get you the replacement red and amber trailer marker lights to replace the SAE AP2 17 DOT. What you need for both are the following: - Red: LED Clearance or Side Marker Trailer Light #MCL0030RBB…

view full answer...

Answer 2

In order to hook up a Blackstone Tailgater to the quick disconnect port on the side of a trailer you should be able to use the MB Sturgis RV Quick-Connect Propane Grill Hose part #100304-60-MBS or part #100304-120-MBS. I called Blackstone and they…

view full answer...

Answer 3

You are right that the gray port is right next to the diagnostic port under the dash on your 2002 Ford F-150 for the brake controller. I have attached a photo that shows where the brake controller port is in relation to the location of the diagnostic…

view full answer...

Answer 4

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 5

The Prodigy P-3 #90195 brake controller will go into a power saving mode after 15 minutes without motion, once the vehicle ignition is turned off. The simple answer to your question is yes, but because the unit goes into power-saving mode, and…

view full answer...

Answer 6

The functionality of the Prodigy P2 and P3 is basically the same with the difference in the controllers being the LCD display in the P3. Both controllers can be used with both electric brakes and electric over hydraulic brakes however with the P3 all…

view full answer...

Answer 7

A deep cycle battery with at least 650 CCA will be your best option for the powering the Bulldog Winch #BDW15018 that you referenced. AGM batteries are considered to be a lead acid battery as well.

view full answer...

Answer 8

It sounds like the tilt battery is backfeeding onto the breakaway battery charge line so as long as the ground is connecting it is taking a charge from the tilt battery and that is why your charge light is staying on. I have a solution for you, you…

view full answer...

Answer 9

You can isolate the break away battery from the auxiliary battery using the Battery Isolation Solenoid #PK5231201. The auxiliary power supply that is needed on this solenoid can be the running lights of your trailer. That way, when your trailer is…

view full answer...

Answer 10

The correct way to wire your breakaway battery, like the Hopkins Engager #20400, is to have the black wire from the battery connected to the 12V power on your trailer, and then the blue wire to your breakaway switch which, in turn, connects to the…

view full answer...

Answer 11

For a stake pocket that you could weld to the side of your trailer that would allow you to make your own walls for the trailer you could use the part #HW03-080. The inner dimensions of the stake pocket are 3-1/2" (w) x 1-9/16" (deep). This…

view full answer...

Answer 12

There is no mounting hardware included with the Aluminum A-Frame Trailer Tongue Toolbox, item #350970, due to the different construction and mounting locations that may be required for many different styles of trailers. I would recommend using a…

view full answer...

Where Is Brake Controller Install Port for 2003 Ford F-150

Featured Help Information

Miscellaneous Media

Continue Researching