Size of Threads on the Replacement D-Spud for Bathroom Sink Diverter Faucets # PF273001

Question

Question:

I have a 1975 traveleze trailer d-spud missing.Bought one at store to small need 3/8 ?

asked by: Buster

1

Helpful Expert Reply:

I went and pulled a Replacement D-Spud for Bathroom Sink Diverter Faucets # PF273001 and determined that it has 7/16 inch fine threads.

expert reply by: Jameson C

1

Answer 1

Hi Ken, The rooftop unit is just a condenser, which is kind of the same setup as a residential system. It just turns on when the controller tells it to which is why it's the only part you can really swap out without having to completely replace…

view full answer...

Answer 2

There are 4 potential problems that are stated in the instructions that could cause the n.c. (no connection) reading on your Prodigy P2, part #90885. I am including a link to the instructions for the Prodigy P2 brake controller. The 4 possible causes…

view full answer...

Answer 3

We have the Replacement D-Spud for Phoenix Faucets RV Tub and Shower Diverter Faucets, #PF183007 that matches as a replacement part for your Phoenix Faucets, #PF213332.

view full answer...

Answer 4

The D-Spud of the Phoenix Faucets RV Bathroom Faucet w/ D-Spud #PF212342 is the threaded outlet on the top of the faucet that will allow you to hook up a handheld shower attachment to your faucet. Simply screw on a shower attachment like #PF276045 to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Nelson, so you would need two separate systems since a supplemental braking system can only be used with a towed vehicle and a trailer brake controller can only control trailer brakes. Main difference is a supplemental braking system is designed…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Size of Threads on the Replacement D-Spud for Bathroom Sink Diverter Faucets # PF273001

Product Page this Question was Asked From

Continue Researching