How Tall is the Ball Part of B&W Gooseneck Ball GNXA2000

Question

Question:

From bed how tall is ball on turnover ball for 2005 superduty

asked by: Kent

0

Expert Reply:

I went out to our warehouse and pulled B&W gooseneck ball # BWGNXA2000 to measure the height of the ball portion. It is approximately 4-1/16 inches from the square base to the top of the ball.

expert reply by: Michael H

0

click to enlarge

Answer 1

I went out to the warehouse and pulled Offset Ball for B&W Turnoverball Gooseneck Trailer Hitches #BWGNXA4085 to measure it. The ball itself is about 5 inches tall from the top of the platform. The platform is 3/4 inches thick. The overall height…

view full answer...

Answer 2

Hey Jeffrey, the Andersen Ultimate Connection 5th Wheel Trailer Hitch System #AN67VR is only designed to attach to the truck by the gooseneck ball that is in the truck bed. This is more of a universal type fifth wheel hitch solution and would not…

view full answer...

Answer 3

This does happen every now and then, but you will need the Dexter Replacement Emergency Breakaway Cable Kit #DX64XR. This is specifically for the A-60 actuators, which the #DX56FR is. With that said, on the bottom or underneath side of the inner…

view full answer...

Answer 4

Hey Ron! Sorry to hear that happened. Have you asked them to replace it? The Mighty Cord Replacement RV Power Inlet #A10-30INBKVP door isn't available separately but it can be replaced. You can remove the four screws from the cover which will…

view full answer...

Answer 5

Hey Mark, we have the RetraxPRO MX part #RT80485 that is a confirmed fit for your 2024 GMC Sierra 3500 long bed. The fit of this is not based on the OEM puck kit as that would not affect anything related to the cover. Are you wanting to cover a fifth…

view full answer...

Answer 6

Hey John! The Gen-Y Hitch Nomad 5th Wheel to Gooseneck Pin Box #GY37ND is not Lippert approved yet. This is designed to replace a pin box with a Lippert Rhino bolt pattern, and is the same exact length as the factory pin box. Gen-Y does stand behind…

view full answer...

Answer 7

Shane, sorry to say we don't have a replacement hardware kit by itself for the B&W Turnoverball #BWGNRK1313. The hardware actually does not look like it's offered by B&W themselves, unfortunately. What I did instead is attach a…

view full answer...

Answer 8

Hey Paul, if you have a 10 inch drum on your Timbren Axle Less setup the correct hub/drum replacement would be the part #AKHD-655-35-K that you referenced. This is very likely what you have but I would still measure what you have again to be sure and…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hello Steven, You will want to use a 3 1/2" bit as you need a 3 1/2" hole for the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs #BWGNRK1320. I attached an image where it goes over the size…

view full answer...

How Tall is the Ball Part of B&W Gooseneck Ball GNXA2000

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching