Your Kuat Ibex truck bed rack is decked out with the panel kit, but now it's time to make room up top for your gear. These risers add 3" to 4" of lift to your crossbars.
This 48" cable can be used to connect a solar charge controller to an RV's SAE port. The wire ends can also be used with a new connector part to create a simple adapter cable.
When your old ceiling assembly gets loud, brittle, or stops moving air, it makes your RV hot. This GE Appliances replacement box makes it feel livable again - getting your air flowing without rewiring walls or messing with complicated controls.
You're swapping out your RV's AC and need the rest of the system to match. This installation kit from GE Appliances gives you the air distribution box, wall thermostat, and control board you'll need to complete a ducted setup.
J-style racks can tap out with wide yaks. This kit adds full-length, padded support to your truck or trailer - no pressure points, no hull dents, no wobble. Perfect for fishing kayaks or any setup that needs more than a strap and a prayer.
Get built-in soft start protection for your entire RV. Start ACs without a bulky generator and get added safety of surge protection and EMS built into one unit.
Dragging your trailer around by brute force? Not anymore. Now you can just roll it into place without throwing out your back. Line up with your hitch, squeeze into storage, or make last-minute adjustments at camp - your back will thank you!
Replace the gasket on your roof-mounted RV air conditioner with this Steele Rubber EPDM sponge rubber gasket. Works with most RV and marine ACs, especially Dometic and Coleman air conditioners.
Use this plate to keep your trailer's king pin from rotating in your PullRite SuperGlide hitch. A capture plate is required for you to tow with the SuperGlide. This plate fits Rota-Flex pin boxes with skid plates that are 13-5/8" wide.
Use this plate to keep your trailer's king pin from rotating in your PullRite SuperGlide hitch. A capture plate is required to tow with the SuperGlide. This plate fits Lippert 1621, 1116, and 1716 pin boxes with 13-1/4" wide skid plates.
Air distribution box for ductless systems lets you replace or upgrade an existing box, or add a new box, in your RV. Just use a wall thermostat (sold separately) to set the temperature and fan speed. Ultra-quiet airflow provides peaceful cooling.
If you only have a couple steps up outside your RV door, this shorter telescoping handrail will be a better size. The 48" rail folds flat against your RV with a sleek, low-profile look that won't obstruct the door.
This stainless steel acorn lug nut laughs in the face of rust. Perfect for saltwater use, it stays strong and rust-free. No chipping, no peeling, just a tough, reliable fit that shrugs off moisture, salt, and road grime for the long haul.
Steel shank allows you to connect almost any weight distribution system. The shank measures 8" long from the center of the hitch pin hole to the center of the adjustment holes. Adjustable height to level with trailer. Fits 2-1/2" receivers.
Get built-in soft start protection for your entire RV. Start ACs without a bulky generator and get added safety of surge protection and EMS built into one unit.
Designed to work with your etrailer scissor jacks, this unique socket is used with your power drill to extend and retract your jack up to 10 times faster than with a manual crank. Works with 3/8" drill bits.
Replaces a diverter valve plumbing assembly on your B&B water control panel. Works with diverter system on all water centers from B&B. Consists of a diverter T-fitting and PEX fittings.
If you need to disconnect the battery to flat tow your vehicle, you're going to want this kit. It disconnects your battery with the turn of a knob - much safer and faster than doing it yourself - while keeping your towing accessories charged.
Get some added traction with these slip-resistant and marine-grade step treads. These step treads are designed specifically for the MORryde Gen II StepAbove 4-step with 23-1/2" treads. Applies quickly and easily with adhesive backing.
Replaces the #05 rubber shear spring on MORryde's rubber pin boxes for trailers between 14,001 - 18,000 lbs GVWR. Helps absorb and dampen road shock, vibration, and reduces chucking. Installs on the skid pad with your existing hardware.
Don't let a flat tire stall your adventure. With this spare mounted on your trailer, just pull over, swap it, and keep rolling. No detours to a repair shop - just a quick fix that gets you back on the road and to the water where you belong.
Filter Results
