Replaces the control keypad on your MAXXAIR MaxxFan Plus roof vent. Works with 4700CN, 4700G, 4900G, 4700D, 4900D, 4700N, 4900N, 4700CN, 4751KS, 4951KS, 4951KSC, 74951KS, and 74751KS model fans.
Replace your damaged MegaSport trailer fender with this direct-fit galvanized steel upgrade. Fits MPG535, MPG550 & MPG595. Rust-resistant, road-tough, and ready to protect your gear from grit, debris, and highway spray.
Mount this rugged rack on your Malone trailer to haul a heavy e-bike up to 200 lbs. Extra-long tray, built-in ramp, and padded locking arm make loading and transport easyeven with fat tires and wide axle spacing.
J-style racks can tap out with wide yaks. This kit adds full-length, padded support to your truck or trailer - no pressure points, no hull dents, no wobble. Perfect for fishing kayaks or any setup that needs more than a strap and a prayer.
Swap out bent or corroded fender brackets on your Malone MegaSport trailer with this factory-style replacement. Built tough to handle road abuse and keep your galvanized fender secure on MPG535, MPG550, and MPG595 models.
Don't let a flat tire delay your adventure. This full-size spare is made for Malone's off-road trailers and includes a lockable mount that secures directly to the frame, so it stays put when the road gets rough.
Adding cross rails to haul extra gear shouldnt mean giving up your tonneau cover. This adapter lets your TradeSport rack mount over select retractable covers, so you can keep your bed protected while carrying boats, ladders, or anything else up top.
Why choose between bed rails and a tonneau cover. This adapter lets you mount a CrossBed rack system without ditching your current, or future, set up. No drilling required. Giving you a clean solution that works with what you've got.
Replaces the extension plates for your Chock-N-Lock wheel stabilizers (71001-BX). Expands your wheel chock to stabilize your trailer when parked. Includes one pair of plates.
Heavy-duty, stainless steel locks provide superior security when locking your B&W hitch step to your B&W Tow and Stow 2" or 2-1/2" ball mount. Third-party-tested pin has a 42,000-lb shear strength.
Replaces the rubber gaskets on your LaSalle Bristol black-water waste valve. Prevents sewer water from slowly leaking out of the valve. Includes two seals for both sides of the valve.
Pipe assembly connects both drains in your dual-basin sink to a single 1-1/2" pipe. Seals included. Made of ABS plastic. Measures 11" center to center.
This 1/2" cone washer creates a watertight seal in your RV's PEX plumbing system. Seats snugly in faucet or toilet fittings to stop leaks and keep your fresh water lines drip-free.
Replaces the stopper in a LaSalle Bristol drains for bathroom sinks. Includes ring seal so you can fill your sink with water without it slowly draining out.
Need an air distribution box for your ductless Furrion Chill Cube RV AC setup? This low-profile unit includes a remote control that can sense and adjust the temperature of the area in your RV that the remote is in.
Need a tough, reliable connection from your actuator to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.
This 23' hose gives you the length to run a brake line from your actuator to the axle on longer trailers. The extra reach lets you make a full connection without adding couplers or mid-line fittings.
This stainless steel acorn lug nut laughs in the face of rust. Perfect for saltwater use, it stays strong and rust-free. No chipping, no peeling, just a tough, reliable fit that shrugs off moisture, salt, and road grime for the long haul.
Use this plate to keep your trailer's king pin from rotating in your PullRite SuperGlide hitch. A capture plate is required for you to tow with the SuperGlide. This plate fits Rota-Flex pin boxes with skid plates that are 13-3/8" wide.
Use this plate to keep your trailer's king pin from rotating in your PullRite SuperGlide hitch. A capture plate is required for you to tow with the SuperGlide. This plate fits Rota-Flex pin boxes with skid plates that are 13-5/8" wide.
Use this plate to keep your trailer's king pin from rotating in your PullRite SuperGlide hitch. A capture plate is required for you to tow with the SuperGlide. This fits Lippert Rhino Box pin boxes with skid plates that are 7-3/8" wide.