# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
What can I say that you haven't already heard? etrailer.com made this such a painless and straight forward process for selecting the front hitch for my 2015 Jeep Rubicon Unlimited that I can't believe I didn't do it sooner. The Curt front hitch for my jeep arrived quickly and in great shape, very well packed. On unpacking I found my hardware and instruction firmly secured to it so it didn't get mixed up with my rear hitch, good forward thinking. The hitch is robustly built and you can see the care that goes into the quality, all the welds are neat and tidy and the finish is excellent. The hardware is all coated for long lasting performance and the fish wire is beyond handy. For the installation of the front hitch the instructions are a little lacking. This is not to say bad or confusing, just lacking a little more how to. The etrailer video on installing it made the process go smooth and easy. On my Rubicon model you do have to fight with the sway bar motor on the passenger side and the vacuum unit on the driver side, it is a pain but if you take the top frame trim off it is much easier to work. The bolt hole on the drivers side, pass a drill through it to make sure the ft is right because its very tight to work in that area and close won't work. Other than that, it installs exactly like the video. The only thing that would complete the package would be a template for clipping the front plastic shield, the Curt instructions include a sketch that gives you an idea but a simple temporary adhesive template would make it super simple to drill the corners out and then connect the dots with a tool of choice. But hey, that's just me. The hitch tucks up real nice and doesn't kill approach angle or ground clearance which is great for my application as its for carrying a winch when I need it. I would recommend etrailer.com without hesitation and strongly urge the Curt line of products based on what I've seen so far.
It was a great price to solve my problem of how to take my bike camping when I’m pulling my teardrop trailer. Installation wasn’t that difficult with the exception of the top bolt on the drivers side. The brake booster pump was in the way. Keep trying and you’ll get it in eventually. It took me about an hour to install.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fit was tight but with a floor jack I was able to install. Looks like it will work well for me. The bolt guide wires were critical to installation. Very good construction of the hitch.
After correcting a mistake and taking another receiver back at their expense, etrailer shipped me the correct hitch for my 2017 Jeep Wrangler Rubicon Recon. If your Wrangler has the steel Hard Rock / Anniversary Edition bumper in the attached pictures, this is the right receiver. It's very well made and has a much better paint job than the Draw Tite that didn't fit my Jeep. The tolerances are VERY tight, so much so that I had to hammer it into place with a block of wood. The supplied fishwires made getting the carriage bolts and spacers in place a breeze. Unfortunately, you will have to remove the steel skid plate that's attached to the bumper. I thought it might be possible to cut it around the hitch and put it back, but it doesn't look there's enough clearance. Great service from etrailer!
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Jeep WranglerFits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
Product shipped and received on time. I'm very happy with the packaging. Hardware was included with instructions to install the hitches I purchased.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I'm off to overland in Texas and wanted you to know that the hitch and winch carrier are perfect. Using quick connectors, I can use ir on the front and rear. Removing it also saves on gas. It works great with a moulded number, saving on buying a specialized steel bumper and other expensive attachments. I like that I can still have all the internal mud guards and brush cover without having to take them off and not be able to have them on. Awesome!
This is a high quality hitch that fits the Gladiator perfectly. The hardest part of the installation was removing and reinstalling the push fasteners on the plastic air dam. While the hitch fit is perfect, the instructions for cutting the plastic air dam leave something to be desired. I finally had to eyeball the location for the hole and then found that the suggested utility knife simply wouldn't cut the plastic air dam. An oscillating saw solved the cutting problem easily and the best guess location worked out. Am I happy with the end result? You bet! Would I do it again? Absolutely.
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."